Search found 54 matches
- October 4th, 2005, 6:15 pm
- Forum: Transmissions
- Topic: How long do these trannies last, on average?
- Replies: 13
- Views: 1845
You should do an oil change every 50 000 kilometer but if you buy a car that has more the 100 000 kilo and the oil was never change i wouldn't sugest it. Automatic transmission fluid act has a detergent, with time the clutch in the transmission gets worn and the particule goes in the oil. If you hav...
- November 28th, 2003, 8:54 pm
- Forum: Forced Induction
- Topic: a F25M-R or G25M-R
- Replies: 31
- Views: 3119
Re: a F25M-R or G25M-R
Don't worry about the tranny guys i've been running my gtx engine on my g25 tranny all summer and it survived (did about 100run on 1/4 this summer) and i have a friend that has his on the f serie tranny and it survived has well. P.S. don't worry about the tranny breaking at 300hp it's not has easy h...
- June 10th, 2003, 9:19 pm
- Forum: 4-Cyl. Technical/Performance
- Topic: stoppid drain plug
- Replies: 1
- Views: 69
Re: stoppid drain plug
Had the same trouble on my first protege the cubber gasket broke.
- June 10th, 2003, 9:17 pm
- Forum: 4-Cyl. Technical/Performance
- Topic: Complete 1.8l protege swap
- Replies: 2
- Views: 68
Re: Complete 1.8l protege swap
His there anything else, the speedo doesn't matter i will leave the electronic speedo has it's not plug in the ecu.
- June 9th, 2003, 9:15 pm
- Forum: 4-Cyl. Technical/Performance
- Topic: Complete 1.8l protege swap
- Replies: 2
- Views: 68
Complete 1.8l protege swap
My friend already had the bp engine in his car now we have found a donor car for the tranny, wiring harness and ecu. I need to find the difference in the wiring harness that goes to the cluster
- May 31st, 2003, 12:11 am
- Forum: 4-Cyl. Technical/Performance
- Topic: BP engine swap
- Replies: 7
- Views: 161
Re: BP engine swap
Adam here in Quebec use the 1.6l transmission in his 323gtx pre89 and his running 356whp on that little tranny. For information about his car go on montrealracing forum and look for turbo323 or 323turbo his the one i'm talking about.<p>How your car running i did the same swap in a friend rs 94 about...
- May 31st, 2003, 12:00 am
- Forum: 4-Cyl. Technical/Performance
- Topic: BP engine swap
- Replies: 7
- Views: 161
Re: BP engine swap
Adam here in Quebec use the 1.6l transmission in his 323gtx pre89 and his running 356whp on that little tranny. For information about his car go on montrealracing forum and look for turbo323 or 323turbo his the one i'm talking about.
- May 25th, 2003, 12:30 am
- Forum: 4-Cyl. Technical/Performance
- Topic: need to adjust the vane airflow meter
- Replies: 1
- Views: 71
need to adjust the vane airflow meter
Okay here's the deal i swapped a gtx engine in my pro lx now i adjusted the vaf so i had a good idle now i want to adjust the spring that make the tension on the bar that move when the air come in has there's to much fuel on boots. I saw a screw on the side of the vaf with a lock nut i think it's th...
- April 21st, 2003, 12:05 am
- Forum: Forced Induction
- Topic: problems with boost(control)
- Replies: 1
- Views: 77
Re: problems with boost(control)
The wastegates must be plug before the throttle body that's why you have 14psi, the wastegate never open. Make shure you Apexi sytem takes his feed from before the throttle body.
- April 13th, 2003, 9:10 pm
- Forum: Suspension/Brakes/Wheels/Tires
- Topic: 4 cyl lower tie bar
- Replies: 3
- Views: 165
4 cyl lower tie bar
Can i put the v6 lower tie bar in front on a rs 94 4 cyl. I cannot find the hole for the bolts
- April 1st, 2003, 7:34 pm
- Forum: 4-Cyl. Technical/Performance
- Topic: NEED THIS DONE TONIGHT
- Replies: 3
- Views: 66
Re: NEED THIS DONE TONIGHT
Good luck doing it at home. The bearing his in the center of the spindle and there's the cage that will be on the hub. to remove the bearing from the spindle you need a press and to remove the cage from the bearing you need a set of torch. you heat the cage until it's red then you put it into water ...
- March 26th, 2003, 7:02 pm
- Forum: 4-Cyl. Technical/Performance
- Topic: 1.8L DOHC BP ENGINE QUESTION
- Replies: 14
- Views: 262
Re: 1.8L DOHC BP ENGINE QUESTION
Straight axles from experience work done it on my friend precidia rs 94 when i put my old bp in his car.
- March 24th, 2003, 7:12 pm
- Forum: 4-Cyl. Technical/Performance
- Topic: HELP! BAD tranny leak question
- Replies: 2
- Views: 59
Re: HELP! BAD tranny leak question
Have you done a lot of burn or made one wheel spin faster then the other in winter. If yes you may have a trouble with the differential. It's not uncommun on mazda transmission
- March 23rd, 2003, 10:26 pm
- Forum: 4-Cyl. Technical/Performance
- Topic: Have question about auto tranni??
- Replies: 13
- Views: 194
Re: Have question about auto tranni??
Oh and the auto from the v6 doesn't fit on the four has the bell housing are different and the starter his on top of the transmission. If you had a v6 i would have recommended a professional shop has it's not easy has a 4 cyl. Personnaly at the shop i prefer v6, take more time to due.
- March 23rd, 2003, 5:34 pm
- Forum: 4-Cyl. Technical/Performance
- Topic: Have question about auto tranni??
- Replies: 13
- Views: 194
Re: Have question about auto tranni??
I'm not shure the mx-6 his a direct fit. But if you have the all car you should be apply to do it. By the way a recondionned trans for a mx-3 his about 1500$ canadian so personnally i would go with the mx-6 swap if you have the entire car