Search found 707 matches
- April 17th, 2012, 9:55 am
- Forum: MX-3 Worklogs
- Topic: Mi|<e - 94 GS BPT dyno tuned
- Replies: 320
- Views: 58411
Re: Mi|<e - 94 RS BPT dyno tuned
So the turbo has been rebuilt, bit expensive but they did a really nice job. New turbine wheel which is a little bigger than the previous one: http://i147.photobucket.com/albums/r298/mikefoo/IMAG0151.jpg http://i147.photobucket.com/albums/r298/mikefoo/IMAG0150.jpg http://i147.photobucket.com/albums/...
- April 13th, 2012, 11:58 am
- Forum: Engine Electronics/Tuning
- Topic: distributor problem
- Replies: 6
- Views: 4386
Re: distributor problem
It sounds like you have made up your mind already and if such this forum can't be of further assistance on the matter. If you would like to possibly save yourself 500 dollars on parts that may not need to be replaced keep reading. The oil in the distributor can be normal with a leaky seal, depends w...
- April 12th, 2012, 9:34 am
- Forum: Engine Electronics/Tuning
- Topic: distributor problem
- Replies: 6
- Views: 4386
Re: distributor problem
The operation of the distributor and leaking oil are not related at all. The distributor herein referred to as 'disty' has an o-ring seal that is a pain to seal correctly. Since you said valve cover (singular) I'll assume 4 cylinder until corrected. You can pick up a valve cover gasket and disty o-r...
Re: Fail
What is wrong with are team?
- April 1st, 2012, 10:08 pm
- Forum: MX-3 Worklogs
- Topic: Mi|<e - 94 GS BPT dyno tuned
- Replies: 320
- Views: 58411
Re: Mi|<e - 94 RS BPT dyno tuned
Ive done more work on the car this weekend. The worst part was lifting the block up into the transmission from below. When I do this next im going to take out the entire engine on my engine hoist. http://i147.photobucket.com/albums/r298/mikefoo/IMG_1025.jpg Looks pretty clean. http://i147.photobucke...
- March 21st, 2012, 2:13 pm
- Forum: 4-Cyl. Technical/Performance
- Topic: HELP! HALTECH E6K TO BPT DISTY/IGNITION??!
- Replies: 10
- Views: 2745
Re: HELP! HALTECH E6K TO BPT DISTY/IGNITION??!
Maps are fairly custom, depends on injector size mostly.
Are you using MAP sensing ?
Are you using MAP sensing ?
- March 19th, 2012, 6:32 pm
- Forum: 4-Cyl. Technical/Performance
- Topic: HELP! HALTECH E6K TO BPT DISTY/IGNITION??!
- Replies: 10
- Views: 2745
Re: HELP! HALTECH E6K TO BPT DISTY/IGNITION??!
Denis did a good write up for the E6K that might help.
http://www.clubprotege.com/forum/showth ... -BP-engine
I have an E6X that is somewhat different.
http://www.clubprotege.com/forum/showth ... -BP-engine
I have an E6X that is somewhat different.
- March 12th, 2012, 8:37 pm
- Forum: MX-3 Worklogs
- Topic: Mi|<e - 94 GS BPT dyno tuned
- Replies: 320
- Views: 58411
Re: Mi|<e - 94 RS BPT dyno tuned
Finally got some new supertech piston rings to re ring the pistons, thanks goes to RS_OBD'oh_2 for these: http://i147.photobucket.com/albums/r298/mikefoo/IMAG0128.jpg I had to borrow a piston ring gapping tool, its just a hand crank stone on a platform: http://i147.photobucket.com/albums/r298/mikefo...
- March 12th, 2012, 10:25 am
- Forum: 4-Cyl. Technical/Performance
- Topic: t25 turbo hp
- Replies: 2
- Views: 1325
Re: t25 turbo hp
Tranny doesn't really make a difference in power, just when it will break. Note I say when and not if. So lets say your wastegate spring is set at 8 lbs. with a 1.8L that can be anywhere from 170-200 horsepower at the crank. So as for a clutch get the spec full face stage 2, iirc its about ~40 bucks...
- March 10th, 2012, 4:12 am
- Forum: 4-Cyl. Technical/Performance
- Topic: 1.8 bp swap wiring harness qustion
- Replies: 4
- Views: 1647
Re: 1.8 bp swap wiring harness qustion
These are the wiring differences for a B6 DOHC to Protege BP05
![Image](http://i147.photobucket.com/albums/r298/mikefoo/WireSwaps-1.jpg)
![Image](http://i147.photobucket.com/albums/r298/mikefoo/WireSwaps-1.jpg)
- March 7th, 2012, 8:42 am
- Forum: Off-Topic
- Topic: Looking to buy a new LED HDTV, opinons wanted
- Replies: 16
- Views: 2399
Re: Looking to buy a new LED HDTV, opinons wanted
Ive had a 7000 series Samsung LED tv since 2010, no problems, its good stuff. When
you are going to purchase it just be ready to walk away to get the best deal.
you are going to purchase it just be ready to walk away to get the best deal.
- March 6th, 2012, 9:44 pm
- Forum: MX-3 Worklogs
- Topic: Sleeper6's Gold 92GS Updated paint pics!
- Replies: 243
- Views: 65890
Re: Sleeper6's Gold 92GS Rebuild opinions wanted!
Beck/Arnley pump from rockauto , 150 bucks
- March 4th, 2012, 12:05 am
- Forum: MX-3 Worklogs
- Topic: Tavman's - 93 White BPT
- Replies: 256
- Views: 47307
Re: Tavman's - 93 White MX3 BPT (Gasket Questions!!)
Topline from http://www.importperformanceparts.net/ just as good as oem
- February 25th, 2012, 2:16 pm
- Forum: V6 Technical/Performance
- Topic: canada members please help me out!!
- Replies: 21
- Views: 493
Re: canada members please help me out!!
This my my crank bolt tool: http://a116.g.akamai.net/7/116/8068/infinite/www.canadiantire.ca/media/images/products/images/Workshop/PowerTools/Drills/CordedDrills/0542734_450_CC_v1_m56577569830660635.jpg They go on sale at canadian tire for 50 bucks from time to time, pretty invaluable thing to have.
- February 25th, 2012, 1:59 pm
- Forum: MX-3 Worklogs
- Topic: Mi|<e - 94 GS BPT dyno tuned
- Replies: 320
- Views: 58411
Re: Mi|<e - 94 RS BPT dyno tuned
Fresh head is fresh with reconditioned BP26 turbo cams
![Image](http://i147.photobucket.com/albums/r298/mikefoo/IMG_0993.jpg)
![Image](http://i147.photobucket.com/albums/r298/mikefoo/IMG_0996.jpg)
![Image](http://i147.photobucket.com/albums/r298/mikefoo/IMG_0993.jpg)
![Image](http://i147.photobucket.com/albums/r298/mikefoo/IMG_0996.jpg)