Search found 164 matches
- May 7th, 2003, 4:58 am
- Forum: V6 Technical/Performance
- Topic: temp sensor
- Replies: 11
- Views: 213
Re: temp sensor
What if he connected the heater hose(s)in wrong ...there is a return and a send hose. If he got them backwards could this make the differance? I was wondering about this earlyer when I connected mine ...I labled them, but I didn't notate witch one was the return and witch one was the send. hmmmm.<p>...
- May 6th, 2003, 4:38 pm
- Forum: V6 Technical/Performance
- Topic: temp sensor
- Replies: 11
- Views: 213
Re: temp sensor
Looks like your thermostat is not opening at 180 degrees. Follow the driver side radiator coolant hose to the assembly on the engine. There are 3 bolts you have to remove. The thermostat is in there. Replace it then try again. If you really want to see if the thermostat is bad before replacing it, p...
- May 5th, 2003, 12:46 am
- Forum: V6 Technical/Performance
- Topic: Neutral switch ?
- Replies: 2
- Views: 41
Neutral switch ?
If the neutral switch is cut will the car start or die (if running if the switch goes bad or tears away. The reason I am asking is because I found 2 green wires that were tore from the trans when I removed the K8. Now I am connecting them up but the green wires don't seem to connect to anything visi...
- May 2nd, 2003, 2:35 am
- Forum: V6 Technical/Performance
- Topic: Dead in the water
- Replies: 7
- Views: 98
Re: Dead in the water
Just don't go to ford dealer to get one $748.00 !!!!!!!!!
- May 2nd, 2003, 2:31 am
- Forum: V6 Technical/Performance
- Topic: plz help me
- Replies: 4
- Views: 61
Re: plz help me
I had a very similiar problem on my van. I changed the battery terminal ground wire to a 2 gage wire and the problem went away... cost = $9.99 <p>good luck! <p>Cage
- May 1st, 2003, 7:31 pm
- Forum: V6 Technical/Performance
- Topic: sensor swapping
- Replies: 7
- Views: 135
Re: sensor swapping
only sensor(S) I had to change:<p>Relocated the knock sensor (wire only) from the TB side to the coolant neck side.<p>on 1992 and 1993 Model Mx-3's the water temp sensor is located on the water neck. On all other years as well as ZE engines it is located in or near the radiator. Solution is to take ...
- May 1st, 2003, 7:11 pm
- Forum: V6 Technical/Performance
- Topic: 2.5 klze
- Replies: 2
- Views: 95
Re: 2.5 klze
Street Imports.....<p> The only place I know of that will air ship a KLZE. you are going to need a place that will air ship to Hawaii. I got mine from them ..They are more expensive, but they are a pretty good outfit. The people who work there have done the swap before, so they know what you need. I...
- May 1st, 2003, 12:54 am
- Forum: V6 Technical/Performance
- Topic: Corksport motormounts
- Replies: 4
- Views: 68
Re: Corksport motormounts
email sales@mazdaspeed.net<p>$275.00 + $21.75 shipping 2 weeks inported and to my door. (what bill said) <p>I have not ordered them yet. waiting for money tree to bloom.<p>Cage
- May 1st, 2003, 12:36 am
- Forum: V6 Technical/Performance
- Topic: New Motor In, Keeps dying out.
- Replies: 5
- Views: 93
Re: New Motor In, Keeps dying out.
hmmm...so you think he is running a MAF instead ? The stock 1995 U.S millinia does use a MAF. Are you using the MX-3 VAF ? What ECU are you using ? The J-spec KL-62 is the only Ecu you can run with a MAF.(or a US OBDII ecu.) KL-36 (bigletters) KL31 small letters are for an auto or manual transmissio...
- April 30th, 2003, 12:33 am
- Forum: V6 Technical/Performance
- Topic: Prob with coolant bypass mod need advisement
- Replies: 7
- Views: 79
Prob with coolant bypass mod need advisement
The small coolant hose that is coming from the block to the TB... What the Fell do I run this to ? ...Do I just cap the hose.<p>
Thanks
Cage
Thanks
Cage
- April 29th, 2003, 4:08 am
- Forum: V6 Technical/Performance
- Topic: Crackes in valve cover Danger Will Robinson???
- Replies: 1
- Views: 124
Crackes in valve cover Danger Will Robinson???
Ok..I was sealing everything back up on the KLZE when I noticed the rear valve cover has a multi crackle reflection ....under closer examination most of them go all the way thru the cover and appear on both sides. They look like stress fractures. The valve cover I am talking about is the one the int...
- April 27th, 2003, 9:18 pm
- Forum: Appearance
- Topic: Check out my new paint job
- Replies: 33
- Views: 768
Re: Check out my new paint job
Sweet paint job ..!!
How much did it set you back ? <p>Cage
How much did it set you back ? <p>Cage
- April 27th, 2003, 4:40 pm
- Forum: Appearance
- Topic: I know I shouldn't post this here but it is kind of a t
- Replies: 9
- Views: 103
Re: I know I shouldn't post this here but it is kind of a t
I wanted the red to match ... Yes. I could buy red wires, but nothing looks worst than 10 different shades of blue or in this case, red under the hood..... I am painting my calipers, my timing belt cover and disty cap.....I just needed to know if painting the wires would change the electrical proper...
- April 27th, 2003, 4:21 pm
- Forum: V6 Technical/Performance
- Topic: Act or Centreforce?
- Replies: 13
- Views: 207
Re: Act or Centreforce?
How streetable is that Aaron? Do you use yours as a daily driver ? <p>Centerforce states :<p>Stage 4 - Stage 4 clutches are not recommended for street use due to their aggressive nature. A rigid disk and carrier are used in combination with your choice of Kevlar, carbon or ceramic pads.<p>Not callin...
- April 27th, 2003, 2:21 am
- Forum: V6 Technical/Performance
- Topic: driving me nuts
- Replies: 3
- Views: 215
Re: driving me nuts
Ummm ...if it is that loud, spend the 60.00 bucks and have mazda listen to it. if is is just a clicking/ pinging tap tap noise it is the HLA. The noise is due to non zero-lash between cam lobe & HLA. <p>FIX ... <p>1. Run synthetic for two oil changes (does not add to sludge/varnish & gently ...