Search found 166 matches
- July 4th, 2009, 5:35 pm
- Forum: General Mazda MX-3
- Topic: Tough Decision?
- Replies: 5
- Views: 254
Tough Decision?
Hey all. I love my 1996 MX3 GS, but it's getting long in the tooth (213,000 kms) and has a few problems that I just don't want to spend the money on (leaky gas tank, p. steering pulley, holes in door sills, rust and anonymously dented driver's fender ). I'm looking at a 93 GS tomorrow with very low ...
- July 27th, 2007, 11:06 pm
- Forum: V6 Technical/Performance
- Topic: CEL and HOT exhaust
- Replies: 4
- Views: 206
- July 27th, 2007, 10:39 pm
- Forum: V6 Technical/Performance
- Topic: CEL and HOT exhaust
- Replies: 4
- Views: 206
- July 27th, 2007, 9:59 pm
- Forum: V6 Technical/Performance
- Topic: CEL and HOT exhaust
- Replies: 4
- Views: 206
CEL and HOT exhaust
I've had a blinking CEL for a while now. Over winter, I changed the disty and the crank sensor. The exhaust is really hot, you can feel it in the foot wells, and recently I noticed that the trunk is red hot (melted some plastic items on the floor of the trunk).
Could it be 02 sensors? Cat?
thanks!!
Could it be 02 sensors? Cat?
thanks!!
- May 5th, 2007, 12:02 am
- Forum: V6 Technical/Performance
- Topic: crank position sensor
- Replies: 6
- Views: 608
Yup, it was just as you said. Removed plastic liner, removed passenger front wheel. We also loosened the bracket holding the dipstick in place, and the belt tensioner -- that made it much easier to run the new wire, with room for the sensor, through and behind as the original piece did. It fired rig...
- March 31st, 2007, 6:06 pm
- Forum: V6 Technical/Performance
- Topic: crank position sensor
- Replies: 6
- Views: 608
Thanks, that gives me a good idea of what I'm up against. Fortunately... I belong to the local motorsports club who get together frequently to wrench on each other's project cars. My skills are, shall we say, less than stellar, but I can always be counted on to go on coffee runs. I think our next ge...
- March 29th, 2007, 11:48 pm
- Forum: V6 Technical/Performance
- Topic: crank position sensor
- Replies: 6
- Views: 608
- July 14th, 2006, 9:34 am
- Forum: General Mazda MX-3
- Topic: Shannonville
- Replies: 6
- Views: 501
I took mine to Mosport last weekend, our motorsports club had an hour of lapping during lunch at one of the race series. These little buggers handle really well. Mine is definitely underpowered - on turn 5 which is a wide sweeping uphill, I fell way behind. By the time we reached the Castrol centre ...
- July 14th, 2006, 9:10 am
- Forum: General Mazda MX-3
- Topic: Shannonville
- Replies: 6
- Views: 501
- July 13th, 2006, 10:21 pm
- Forum: General Mazda MX-3
- Topic: Car Parts Depot - anyone familiar with them?
- Replies: 3
- Views: 316
- July 13th, 2006, 9:58 pm
- Forum: General Mazda MX-3
- Topic: Shannonville
- Replies: 6
- Views: 501
- July 9th, 2006, 9:36 am
- Forum: General Mazda MX-3
- Topic: Shannonville
- Replies: 6
- Views: 501
Shannonville
I was at Shannonville Drag strip last night, saw a couple of nice mx-3s... anyone from this site?
Great night for racing but the bugs were awful!!!
(I was the black dakota with the Boyd rims)![Smile :)](./images/smilies/icon_smile.gif)
Great night for racing but the bugs were awful!!!
(I was the black dakota with the Boyd rims)
![Smile :)](./images/smilies/icon_smile.gif)
- June 23rd, 2006, 9:38 pm
- Forum: General Mazda MX-3
- Topic: Time for a service on my MX-3 V6?
- Replies: 5
- Views: 415
- June 23rd, 2006, 9:21 pm
- Forum: V6 Technical/Performance
- Topic: Crank Angle Sensor
- Replies: 43
- Views: 2806
Thanks for clearing that up... I've had my mx for two months and just replaced the disty since I was getting the same code. Two days later, you guessed it, CEL again. An RX7 friend has a code reader, we're going to see if the code is the same. If so, I'm assuming it must be the crank sensor instead ...
- June 9th, 2006, 9:58 pm
- Forum: General Mazda MX-3
- Topic: I want to find my old mx-3
- Replies: 14
- Views: 1471