MX-3.com

so, the one on ebay is us-spec??

http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItem&category=33596&item=2464151085

First things first…I have a klze and having some problems.....with k8 IM, ECU and VAF. 1) Overheating- I know I have a leak somewhere, cuz I see a puddle every morning, and it overheats when it gets low, but by reservoir is full and stays full. My instructor says its probably my radiator cap. So I g...

My car tried overheated, untill i turned my heat on, then it went down extremely quick...any ideas...i have a klze

thanks in advance
Mykil²

Well,
I have a Ze and i used my K8 mainfold, and i have a big leak in the upper right side.. But im using an 97 millinia gasket..So i guess my question is, are they compaible and i just have them on wrong, or do i need to buy a new gasket. ...thanx in advance..

Mykil²

Well, Its running....but terrible, idle is bouncy until warm. Exausht and vacuum leak. Reverse lights stuck on :( . Maybe i expected too much. I had a guy do it for me from school.(Automotive school)And he left off the nuts for the motor mount studs!! :mad: Didnt figure that out till i got home. And...

WEll im going to try to use the EGR. Which would be easier, with or without?? my k8 exauhst manifolds are on there too...

WEll, my ZE is near compleation and all is needed is vacuum hoses. And i was looking at mx6.com and they had some vacuum diagrams for some reason. But i put my K8 manifold on my Ze. So is there anything specail i need to do?? Any help would be appriciated

thanx in advance
Mykil²

I just got my ZE and i need to put my K8 intake and exaust manifold on, but which gasket to i buy. K8 or KL? And since the timing belt cover has japenese writing on it, should i assume that its a KLZE. B/c i dont know exatcly where to look for the ID numbers. Thats all i can think of for right now. ...

I am thinking about purchasing the "Clutchmasters STAGE II "R" 2.5L V6w/ POLY ENGINE MOUNTS Front and Rear" for $330 b/c my ZE in on its way. Does that come with everything i need to replace my old clutch. Like pressure plate, pilot bearing, alignment tool, etc....And are they ju...

I was wondering what parts you take from the K8 to put on your ZE, I need to know so i can get a quote on labor.<p>Thanx in advance,
Mykil²

Well,<p> I did a compression test and the #4 cylinder has no compression at all!! Im trying to get my mom to help me out and get he ze!!

I was driving on the highway. Suddenly, my car dies. I try to start it and it will only keep running if i keep giving it alittle gas. It runns reallly ruff and i hear "valve clack"...My step dad told me my timing belt might have jumped a couple teeth...And is there anywhere to hook up a ti...

Thanx for the help guys!<p>I called the dealer and he said that i could buy the little rubber peices seperatly at 5 bucks a piece. But he also said i need 4 of them?
...zevirii do you have a part number?? It would really help alot. Thanx again<p>Mykil²

R u sure??... Cus the whole shift lever, will fall right out of the floor....Does the shift linkage hold the shifter to the floor board?
thanx<p>Mykil²

I was at a stop light and i was tapping kinda hard on my shifter, and it just droped!! It fell out 3 inches in, and the only think that was holding it up was a rubber O ring...Am i missing parts?? I went to the dealer, and he he didnt know... I dont want to drive it cuz it just keeps getting lower.....