Search found 23 matches
- June 27th, 2007, 9:57 am
- Forum: General Mazda MX-3
- Topic: If you are a meth dealer from Quebec, I found your revolver.
- Replies: 11
- Views: 1453
- June 27th, 2007, 1:13 am
- Forum: General Mazda MX-3
- Topic: If you are a meth dealer from Quebec, I found your revolver.
- Replies: 11
- Views: 1453
If you are a meth dealer from Quebec, I found your revolver.
So I went to the wreckers today to get a front bumper. When I reached inside the engine bay to get a hard to reach bolt I felt a ziploc bag. There was a loaded revolver double bagged sitting near the washer fluid reservoir. Apparently the car belonged to a meth dealer from quebec who dumped the car ...
- June 25th, 2007, 7:37 pm
- Forum: MX-West Car Club (Vancouver, BC / Calgary, AB)
- Topic: I need help locating a radiator!!
- Replies: 2
- Views: 1304
- June 25th, 2007, 1:46 pm
- Forum: MX-West Car Club (Vancouver, BC / Calgary, AB)
- Topic: Moving to Calgary, need exhaust and front bumper
- Replies: 2
- Views: 1170
Thanks for the recommendation. I was going to wait until I got to Calgary to fix the exhaust but the noise is driving me crazy so I've got the car booked in at a place called ABC muffler and hitch in Edmonton for tomorrow. They quoted me a price of $499 for a full exhaust with a magnaflow resonator ...
- June 22nd, 2007, 4:33 pm
- Forum: MX-West Car Club (Vancouver, BC / Calgary, AB)
- Topic: Moving to Calgary, need exhaust and front bumper
- Replies: 2
- Views: 1170
Moving to Calgary, need exhaust and front bumper
Hi! I'm putting my mx-3 back on the road after it sat in my garage for over a year. I'm moving to Calgary for work and need to get a new exhaust system. Could anyone recommend a place to get a decently price performance system installed? I'm going to be using the car for my job so I don't want anyth...
- May 3rd, 2005, 1:57 am
- Forum: V6 Technical/Performance
- Topic: $3000 and big dreams
- Replies: 8
- Views: 492
I dont know about Saskatchewan, but in Alberta mx-3's still sell for between $3500 and $8000 depending on the year and condition. I would think Saskatchewan would have even less of them floating around. You could end up lucky, but I'd start checking the classifieds, autotrader and the bargainfinder ...
- May 2nd, 2005, 2:38 pm
- Forum: V6 Technical/Performance
- Topic: SWAP
- Replies: 15
- Views: 1175
- April 29th, 2005, 3:00 pm
- Forum: V6 Technical/Performance
- Topic: Help me reawaken the beast
- Replies: 16
- Views: 620
- April 29th, 2005, 2:53 pm
- Forum: V6 Technical/Performance
- Topic: E-brake cable. Please help..
- Replies: 2
- Views: 227
ya, the rear calipers are notorious for having the e-brake latch seize. If you want a temporary fix, take off your wheel and pull the e-brake latch back to its normal postion. I have to use rope for leverage on mine. You can try putting some lube in there but if you want to be able to use your e-bra...
- April 29th, 2005, 2:22 pm
- Forum: V6 Technical/Performance
- Topic: Help me reawaken the beast
- Replies: 16
- Views: 620
Problem solved! well, my favorite solution worked on my car. I tried starting it again yesterday and it fired right up. Its not starting as well as it used to, I have to give it some gas to get it to catch, so is there something that could be causing a problem? I think I'll change the rotor cap as i...
- April 27th, 2005, 11:05 pm
- Forum: V6 Technical/Performance
- Topic: Help me reawaken the beast
- Replies: 16
- Views: 620
sorry about taking so long to reply, I'm in the middle of writing final exams. I started the car a month ago just to make sure it stayed lubricated and move the oil around a bit. The car started up fine then so it makes this even more frustating. The plugs were changed recently but I think the wires...
- April 26th, 2005, 6:29 pm
- Forum: V6 Technical/Performance
- Topic: Help me reawaken the beast
- Replies: 16
- Views: 620
Help me reawaken the beast
I tried to start up my car on Sunday after it sat on my driveway for the winter. It was turning over and its getting fuel I think (I could smell the gas after cranking for a while) but wouldnt start, even when I tryed boosting it. It sounds really close to starting, does anyone have any idea whats w...
- October 15th, 2004, 3:34 am
- Forum: Forced Induction
- Topic: dodge/crysler PITA
- Replies: 9
- Views: 393
Re: dodge/crysler PITA
Is the TE04H a good combo with the KLDE? Its going to be a winter project for me and that turbo seemed like the best fit for the car. 2.5L to 2.5L, pretty new and dirt cheap. Whats the wastegate like on it? I only want to run 5-6 psi of boost so it should be able to handle it right?
- October 15th, 2004, 3:30 am
- Forum: Forced Induction
- Topic: dodge/crysler PITA
- Replies: 9
- Views: 393
Re: dodge/crysler PITA
thanks for the great tips. Theres a dodge caravan at my local yard with a T4 that I wanted to get. Theres not really anyway to get underneath so I guess I'll have to take the head off.
- October 12th, 2004, 10:11 pm
- Forum: Forced Induction
- Topic: dodge/crysler PITA
- Replies: 9
- Views: 393
dodge/crysler PITA
How the hell do you get a turbo off of a dodge or crysler. I was at the junkyard going at a shadow but the car had no tires so I couldn't get underneath. Is there any way to get one from the top or do I need to just flip the car over? ![Very Happy :D](./images/smilies/icon_biggrin.gif)
![Very Happy :D](./images/smilies/icon_biggrin.gif)