Check it out :)
-
- Regular Member
- Posts: 260
- Joined: January 4th, 2003, 2:01 am
- Location: Brazil
- Contact:
Check it out :)
Hi guys!!!
Just to let you know about my new cardomain page...it will contains some Mazdas from my "gang" around here (Brazilian Mazda Tuners)....
I'll update it soon with more cars from the group, including mine!!
web page
<img src="http://images.cardomain.com/member_imag ... 7174_2.jpg" alt=" - " />
Just to let you know about my new cardomain page...it will contains some Mazdas from my "gang" around here (Brazilian Mazda Tuners)....
I'll update it soon with more cars from the group, including mine!!
web page
<img src="http://images.cardomain.com/member_imag ... 7174_2.jpg" alt=" - " />
Cris
Re: Check it out :)
That's a sick front end man. What car did you steal it from?
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
Re: Check it out :)
nice and clean man, nice and clean
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
Re: Check it out :)
dittoOriginally posted by Jutzi420:
That's a sick front end man. What car did you steal it from?
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
-
- Regular Member
- Posts: 583
- Joined: September 16th, 2002, 2:01 am
- Location: Hartford, CT
Re: Check it out :)
sweet man. I like it
Sold my 95 RS "Little Peanut" but she will never be forgotten.
-
- Regular Member
- Posts: 260
- Joined: January 4th, 2003, 2:01 am
- Location: Brazil
- Contact:
Re: Check it out :)
The front bumper is the original bumper with some "mods"...
I'm in process to make some parts for the MXers....we'll have a big grake kit avaible soon for around U$900,00, and some special items ...ASAP I'll post some pics....
See yah!
I'm in process to make some parts for the MXers....we'll have a big grake kit avaible soon for around U$900,00, and some special items ...ASAP I'll post some pics....
See yah!
Cris
-
- Regular Member
- Posts: 846
- Joined: October 19th, 2002, 2:01 am
- Location: Ottawa, Ontario, Canada
- Contact:
Re: Check it out :)
Did you mold the GS lip into that front? Then cut a bunch of holes ect? or did you mold on the bottom part of another kit onto the stock bumper? Cuase that looks awsome man, i like it more then the Mazdaspeed front.
Mods:
- ZE, Mike seli 214 intake cams, Ported n polished heads, Interprep valve springs, DE retainers, rebuilt bottom end, toga main and rod bearings, toga hv oil pump, CZT 67mm tb, mbx udp, ported intake mani, SS headers, 2.5inch full exhaust, racingbeat muffler, highflow cat, megasquirt v2.
new toy, 86 TII rx7, JDM S5 motor/turbo, + alot of other goodies
- ZE, Mike seli 214 intake cams, Ported n polished heads, Interprep valve springs, DE retainers, rebuilt bottom end, toga main and rod bearings, toga hv oil pump, CZT 67mm tb, mbx udp, ported intake mani, SS headers, 2.5inch full exhaust, racingbeat muffler, highflow cat, megasquirt v2.
new toy, 86 TII rx7, JDM S5 motor/turbo, + alot of other goodies
-
- Regular Member
- Posts: 260
- Joined: January 4th, 2003, 2:01 am
- Location: Brazil
- Contact:
Re: Check it out :)
It was the first front bumper made....we cutted the original "urethane" bumper and mold the vents in....the lips are stock around here in the RS models too...
We're trying to do the front bumper in fiberglass....when I get some new, I'll post here.
Daniel (the owner), is running 1kg (around 14psi) of boost right now...it's awesome!!!He is using a VW Jetta intercooler (really small!), 1.8 injectors, T25, FMU, etc...no problems until now (at really the only problem is the bad idle...the car idles at 1200rpm...any advice?? Probably the MAF sensor..don't know yet!)...the engine is still stock
We're trying to do the front bumper in fiberglass....when I get some new, I'll post here.
Daniel (the owner), is running 1kg (around 14psi) of boost right now...it's awesome!!!He is using a VW Jetta intercooler (really small!), 1.8 injectors, T25, FMU, etc...no problems until now (at really the only problem is the bad idle...the car idles at 1200rpm...any advice?? Probably the MAF sensor..don't know yet!)...the engine is still stock
Cris
- Custommx3
- Site Administrator
- Posts: 8391
- Joined: November 7th, 2000, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Lat 35.1N Lon -90W
- Contact:
Re: Check it out :)
Why is the front bumper fuzzy in all the pics, u sure thats no Photoshop?
-
- Regular Member
- Posts: 260
- Joined: January 4th, 2003, 2:01 am
- Location: Brazil
- Contact:
Re: Check it out :)
Sorry...no Photoshop here!!
Maybe it's the quality of the photos....
<img src="http://images.cardomain.com/member_imag ... 174_19.jpg" alt=" - " />
<img src="http://images.cardomain.com/member_imag ... 174_20.jpg" alt=" - " />
<img src="http://images.cardomain.com/member_imag ... 174_21.jpg" alt=" - " />
<img src="http://images.cardomain.com/member_imag ... 174_22.jpg" alt=" - " />
Maybe it's the quality of the photos....
<img src="http://images.cardomain.com/member_imag ... 174_19.jpg" alt=" - " />
<img src="http://images.cardomain.com/member_imag ... 174_20.jpg" alt=" - " />
<img src="http://images.cardomain.com/member_imag ... 174_21.jpg" alt=" - " />
<img src="http://images.cardomain.com/member_imag ... 174_22.jpg" alt=" - " />
Cris
- Sam Baker
- Regular Member
- Posts: 1461
- Joined: May 23rd, 2003, 2:01 am
- Location: Wellington, New Zealand
Re: Check it out :)
yea no photoshop cuz he posted a while ago.. MAN such a nice car!! i love that custom kit! but what is this about u guys making a kit to sell?
92 Autozam AZ3
-
- Regular Member
- Posts: 260
- Joined: January 4th, 2003, 2:01 am
- Location: Brazil
- Contact:
Re: Check it out :)
Thanks!It was posted here some time ago to show the Z3 fenders...
Well...we're creating a MX-3 community around here, and it's obvious the lack of aftermarket parts for the MX-3 around the world...specially when you need to pay more than 70% of taxs to bring it
I hope to get some news soon....
Well...we're creating a MX-3 community around here, and it's obvious the lack of aftermarket parts for the MX-3 around the world...specially when you need to pay more than 70% of taxs to bring it
I hope to get some news soon....
Cris
Re: Check it out :)
Did you make the eyelids,because they look different than any of the ones I have seen , much more agressive looking, I like them much better than the jdm ones I see on ebay
Eugene L
1.6DOHC
N.S.canada
http://www.cardomain.com/memberpage/552384
Eugene L
1.6DOHC
N.S.canada
http://www.cardomain.com/memberpage/552384
-
- Regular Member
- Posts: 260
- Joined: January 4th, 2003, 2:01 am
- Location: Brazil
- Contact:
Re: Check it out :)
The eyelids are actually molded in the hood...they welded sheets of iron like this:
<img src="http://www.spportcarbr.net/imagens/168.jpg" alt=" - " />
<img src="http://www.spportcarbr.net/imagens/168.jpg" alt=" - " />
Cris