93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails http://www.cardomain.com/id/blazejeremy
Originally posted by Jutzi420: That's a sick front end man. What car did you steal it from?
ditto
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails http://www.cardomain.com/id/blazejeremy
The front bumper is the original bumper with some "mods"...
I'm in process to make some parts for the MXers....we'll have a big grake kit avaible soon for around U$900,00, and some special items ...ASAP I'll post some pics....
Did you mold the GS lip into that front? Then cut a bunch of holes ect? or did you mold on the bottom part of another kit onto the stock bumper? Cuase that looks awsome man, i like it more then the Mazdaspeed front.
Mods:
- ZE, Mike seli 214 intake cams, Ported n polished heads, Interprep valve springs, DE retainers, rebuilt bottom end, toga main and rod bearings, toga hv oil pump, CZT 67mm tb, mbx udp, ported intake mani, SS headers, 2.5inch full exhaust, racingbeat muffler, highflow cat, megasquirt v2.
new toy, 86 TII rx7, JDM S5 motor/turbo, + alot of other goodies
It was the first front bumper made....we cutted the original "urethane" bumper and mold the vents in....the lips are stock around here in the RS models too...
We're trying to do the front bumper in fiberglass....when I get some new, I'll post here.
Daniel (the owner), is running 1kg (around 14psi) of boost right now...it's awesome!!!He is using a VW Jetta intercooler (really small!), 1.8 injectors, T25, FMU, etc...no problems until now (at really the only problem is the bad idle...the car idles at 1200rpm...any advice?? Probably the MAF sensor..don't know yet!)...the engine is still stock
Thanks!It was posted here some time ago to show the Z3 fenders...
Well...we're creating a MX-3 community around here, and it's obvious the lack of aftermarket parts for the MX-3 around the world...specially when you need to pay more than 70% of taxs to bring it
Did you make the eyelids,because they look different than any of the ones I have seen , much more agressive looking, I like them much better than the jdm ones I see on ebay