[GI] Carbon lips

Sleeper6 · Post by **Sleeper6** » June 25th, 2010, 11:03 pm

Mooneggs wrote:I have a CF front lip and it is 2 pieces... I would definatley recommend making it 2 pieces similar to the OEM design. It will give it a heck of a lot better chance of not breaking while shipping!

any chance of a close up pic?

AaronTietje · Post by **AaronTietje** » June 27th, 2010, 5:35 pm

Mooneggs wrote:I have a CF front lip and it is 2 pieces... I would definatley recommend making it 2 pieces similar to the OEM design. It will give it a heck of a lot better chance of not breaking while shipping!

Thats a good point. Thanks.

Update I just got fiberglass for the backing. It is a very good boat grade weave.

AaronTietje · Post by **AaronTietje** » August 10th, 2010, 10:34 am

Hi again guys and gals, just an update. I am still looking for a front lip

Once I have that I will begin the mold work.

Thanks Aaron

pattheriault · Post by **pattheriault** » February 9th, 2011, 1:29 pm

are you still planning on doing this lip?

Sleeper6 · Post by **Sleeper6** » February 9th, 2011, 2:31 pm

Pretty sure he is, theres just a shortage of lips in upstate...

AaronTietje · Post by **AaronTietje** » February 9th, 2011, 11:04 pm

I am still planning on doing this, however, I only have a busted up lip in my posession.

If I don't find a good lip I will have to repair mine an make the mold from it.

pattheriault · Post by **pattheriault** » February 11th, 2011, 11:43 am

id send you one but I dont have any lol!

would def. be interested in a carbon one if this work out.

AaronTietje · Post by **AaronTietje** » February 13th, 2011, 4:24 pm

pattheriault wrote:id send you one but I dont have any lol!

would def. be interested in a carbon one if this work out.

LoL thanks buddy.

PATDIESEL · Post by **PATDIESEL** » February 14th, 2011, 5:59 pm

ugh, I am still interested too. Post a thread asking for cheap lip pieces on MOCA. www.atlantamx3.com/mocaforum I think we might have two decent sides if we (MOCA) put two together. I know I have a ok one that I was saving for just such a molding process, but I am too busy.

RedAutobotMX3 · Post by **RedAutobotMX3** » February 26th, 2011, 6:34 pm

Def would love one of these +1

FastFlaMx3 · Post by **FastFlaMx3** » March 20th, 2011, 11:28 am

i would love to have one too

MrMazda92 · Post by **MrMazda92** » September 6th, 2011, 12:51 am

Nobody load your guns over this, but....

J-Spec mini sides.

I would rock a JDM lip if the sideskirts weren't full length. I think this would be the sexiest look ever for an MX-3.

It couldn't be too hard to mock one up either, using Euro mini sides and JDM full lengths to design it.

ethand · Post by **ethand** » September 9th, 2011, 9:23 am

I think the user -eunos- has a mold for the JDM lip... He was going to do a run of them... He's selling his Eunos now, though, so might not be too keen. Also, he's here in Australia (but on the other side to me!), so postage might be a bit...
Still, might be worth shooting him a PM...

Sleeper6 · Post by **Sleeper6** » September 9th, 2011, 10:22 am

Winters coming soon So we might be able to talk aaron into making some copies of my lip when its off for the season, its a bit more aggresive but if theres interest Ild be willing to let him make molds of it.

MrMazda92 · Post by **MrMazda92** » September 10th, 2011, 3:08 pm

There's a GS lip for sale in the [FS] section right now, $80.

MX-3.com

[GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips

Re: [GI] Carbon lips