egr valve went out.
-
- Junior Member
- Posts: 23
- Joined: April 27th, 2008, 6:52 am
egr valve went out.
I need to buy a new one.. is it hard to replace yourself? I don't know much about cars. My mx3 has a ford probe gt engine. so can I buy the egr valve for the ford probe, or do I have to buy the mx3 one.. its about 100 dollars more expensive..
- Kirk95gs
- Supporting Member
- Posts: 820
- Joined: July 21st, 2006, 10:02 am
- Location: Nova Scotia/New Bunswick
- Contact:
Re: egr valve went out.
It's a little work if you have never done it befor. Use the online Manual for the step by step. If your low on funds get one from the junk yard. should save you some money. I dont know what the diffrents is between the mx-3 and pgt egr is. Should be the same I would think. Maybe not.
- mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
Re: egr valve went out.
how do you know it went out, sometimes they just need to be cleaned out inside. You have a klde swap in your mx3?
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks
http://www.cardomain.com/id/mitmaks
-
- Junior Member
- Posts: 23
- Joined: April 27th, 2008, 6:52 am
Re: egr valve went out.
yeah
well, i think the guys at the shop know Im not good with cars, so they said i need a new one...
Im 20 and this is my first car.
They said my entire exhaust needs to be replaced and I need to go to a 2in pipe. Aluminum.. egr valve needs to be replaced.. They said my engine has an oil leak..but I never leave a pool...there is just oil on the bottom of the engine and the tranny. Hmm.. My seatbelt don't work right.. Hmm.
Well.. the problem was when I started the car, and put it into first gear, it don't give it gas right.. It goes like 1mph unless I rev it up... and shift into second.. If I can get it into 4th gear it runs great. The first gear is s--- though. It didn't do that until theyn started messing with the exhaust.
All my pipes are rusted and corroded. They said I need a new cat, new resonator, and I need to buy headers. If I can get headers they said the rest of the work would be easier. Im not sure where to get them or what kind. I stink at car stuff, but Im willing to save my money to fix up this car.. I love it. I have only seen 2 mx-3s near this part of Houston, Tx.. and one is a 4cl.. Mine is the only 6
well, i think the guys at the shop know Im not good with cars, so they said i need a new one...
Im 20 and this is my first car.
They said my entire exhaust needs to be replaced and I need to go to a 2in pipe. Aluminum.. egr valve needs to be replaced.. They said my engine has an oil leak..but I never leave a pool...there is just oil on the bottom of the engine and the tranny. Hmm.. My seatbelt don't work right.. Hmm.
Well.. the problem was when I started the car, and put it into first gear, it don't give it gas right.. It goes like 1mph unless I rev it up... and shift into second.. If I can get it into 4th gear it runs great. The first gear is s--- though. It didn't do that until theyn started messing with the exhaust.
All my pipes are rusted and corroded. They said I need a new cat, new resonator, and I need to buy headers. If I can get headers they said the rest of the work would be easier. Im not sure where to get them or what kind. I stink at car stuff, but Im willing to save my money to fix up this car.. I love it. I have only seen 2 mx-3s near this part of Houston, Tx.. and one is a 4cl.. Mine is the only 6
Re: egr valve went out.
A little off-topic off-car question:
Would EGR from KL fit K8?
Would EGR from KL fit K8?
MX-3 V6 1993 | Black | EU-spec | K819
- marcdh
- Regular Member
- Posts: 1460
- Joined: July 26th, 2006, 3:54 pm
- Location: Belfast -Northern Ireland
- Contact:
Re: egr valve went out.
yes the part number actually says kl on it (on my k8s) so does the dipstick, uprated yeow gotta be worth a few hp
AZ-3 1498cc Turbo! EVO 8 turbo and manifold, 5 stud swap, SSR Type C, DIYPNP seq Megasquirt
Mx-3 2.5 V6 Turbo 291 BHP 251 lbft @ 8psi - Retired due to rust and back at uni
View Worklog
Mx-3 2.5 V6 Turbo 291 BHP 251 lbft @ 8psi - Retired due to rust and back at uni
View Worklog
- eyezpinned
- Regular Member
- Posts: 208
- Joined: March 9th, 2006, 2:29 pm
- Location: Philadelphia
- Contact:
Re: egr valve went out.
get a blocking plate and just take it out... the 4 cylinders dont even have an egr valve
93 rs: tokico struts & eibach springs, 15' rota gt3s, cf hood & gas lid, 2.5' exhaust w high-flow cat, tranny cooler, reupholstered seats, custom black interior, chrome miata handles, momo wheel & ebrake, spyder black projector lights w hid, altezzas, clear corners/sides, eclipse 8454 hu, diamond hex components w/ 3-way add-on & an re se 15' powered by 300/2v2 & 500/1 jl slash amps, corksport mazdaspeed bumper, euro mini sideskirts, fresh paint
Re: egr valve went out.
Marcdh, thank you! I've got one spare EGR valve with 21k kms on it and my old in MX3 went out. Good to know it fits.
PS: I don't want blocking plate. I want to have my emissions as low as possible and pass emission tests without any problem.
PS: I don't want blocking plate. I want to have my emissions as low as possible and pass emission tests without any problem.
MX-3 V6 1993 | Black | EU-spec | K819
- marcdh
- Regular Member
- Posts: 1460
- Joined: July 26th, 2006, 3:54 pm
- Location: Belfast -Northern Ireland
- Contact:
Re: egr valve went out.
Whoops I was thinking PCV lol sorry mate But yea some uk-mx3 people have migrated their EGR from K8 to klze, so it's all good Do your emissions testers test for NOx? As that's what it reduces. UK they don't test for it so it's pointless!
AZ-3 1498cc Turbo! EVO 8 turbo and manifold, 5 stud swap, SSR Type C, DIYPNP seq Megasquirt
Mx-3 2.5 V6 Turbo 291 BHP 251 lbft @ 8psi - Retired due to rust and back at uni
View Worklog
Mx-3 2.5 V6 Turbo 291 BHP 251 lbft @ 8psi - Retired due to rust and back at uni
View Worklog
Re: egr valve went out.
I want to migrate EGR valve from KL to K8. Yes, they test exhaust gas for everything, it is very strict here.
MX-3 V6 1993 | Black | EU-spec | K819
-
- Junior Member
- Posts: 23
- Joined: April 27th, 2008, 6:52 am
Re: egr valve went out.
I live in Texas, one of the worst states with pollution. Our emissions test is ridiculous. You have to bribe people to pass.
-
- Senior Member
- Posts: 6451
- Joined: June 19th, 2004, 2:01 am
- Location: El Paso Tx U.S
- Contact:
Re: egr valve went out.
hehe I have NO egr and 25 extra bucks shows mine can pass LOL
Just get a JUNK YARD egr.. no sense paying 100 dllrs for a new one unless the scrappers want like 50..
to get rid of the CODE all you need is to connect any EGR. and leave it hanging.
Just get a JUNK YARD egr.. no sense paying 100 dllrs for a new one unless the scrappers want like 50..
to get rid of the CODE all you need is to connect any EGR. and leave it hanging.
-hec
MX-3 w/ curved neck millenia klde, boosted @ 5 psi. /bov and wastegate are good!/ nitto drag radial/ gutted interior/ millenia red top injectors, vortech fmu/aem wideband/ all bolts ons/ Car put together 100% by me. Mechanic? who needs a mechanic? ew.. real men work on their own cars!
MX-3 w/ curved neck millenia klde, boosted @ 5 psi. /bov and wastegate are good!/ nitto drag radial/ gutted interior/ millenia red top injectors, vortech fmu/aem wideband/ all bolts ons/ Car put together 100% by me. Mechanic? who needs a mechanic? ew.. real men work on their own cars!
- zzzoomx3
- Regular Member
- Posts: 470
- Joined: January 31st, 2007, 11:06 pm
- Location: Dallas, Texas
- Contact:
Re: egr valve went out.
sounds like someone could use my exhaust tutorial - i have a catalytic converter and an EGR from my K8 - i live in Dallas and yes - its nice to know people when it comes to inspection time. i left the EGR off my ZE as well as the cat. i'm running just straight pipe all the way to the moofler
so yeah, spartan - if you need a new exhaust, check out my work log and if you need a cat, headers and EGR - hit me up.
so yeah, spartan - if you need a new exhaust, check out my work log and if you need a cat, headers and EGR - hit me up.
Re: egr valve went out.
Please, can anyone tell me if EGR from KL-DE would fit K8-DE? Thank you!
MX-3 V6 1993 | Black | EU-spec | K819
Re: egr valve went out.
NO The EGR from a KL will NOT fit a K8! Part numbers are as follows
K8: K801-20-300A Price CAD: $538.06
KL: KL01-20-300B Price CAD: $396.57
This is from the Mazda dealership I work at.
K8: K801-20-300A Price CAD: $538.06
KL: KL01-20-300B Price CAD: $396.57
This is from the Mazda dealership I work at.