Front Main Oil Seal
- ElectricEnergy
- Regular Member
- Posts: 489
- Joined: August 15th, 2006, 12:37 am
- Location: Saskatoon SK, Canada
Front Main Oil Seal
Hey guys,
I was working on my ZE last night, trying to replace the front main seal, but I can't seem to get it out. Now I've got it all shredded up and its a bit of a mess.... haha. What's the best way to get these out? The shop manual suggests slicing the lip of the seal and removing it with a screwdriver, but that doesn't seem to be working for me.
David
I was working on my ZE last night, trying to replace the front main seal, but I can't seem to get it out. Now I've got it all shredded up and its a bit of a mess.... haha. What's the best way to get these out? The shop manual suggests slicing the lip of the seal and removing it with a screwdriver, but that doesn't seem to be working for me.
David
KL-ZE Swap - OBX SS Headers - 2.5" Exhaust - Falken Azenis Tires - H&R Springs - ZX-2 Struts - CAI - Front & Rear Tower Bar - AWR Motor Mounts - 100hp wet shot (yet to be tested)
Re: Front Main Oil Seal
Get two long thin self tapping screws, and use a drill to drive them into the
seal, the seal will jack itself out on them or you can use vice grips on the
screws to pull it out.
seal, the seal will jack itself out on them or you can use vice grips on the
screws to pull it out.
Re: Front Main Oil Seal
The screw idea is a good one. I would not drive the screws so far to push the seal out unless you grind the screw tip flat. You might also be successful with a couple of curved picks. You just need to be careful that you don't scratch the crankshaft or the machined edge of the seal housing. It doesn't take too much damage to make it impossible - new seal or not - to make an oil tight seal.
Proud owner of a Faded Red 92 MX-3 GS
- ElectricEnergy
- Regular Member
- Posts: 489
- Joined: August 15th, 2006, 12:37 am
- Location: Saskatoon SK, Canada
Re: Front Main Oil Seal
wont the screws scratch the hell out of the crankshaft/housing? Which part of the seal should I screw them into?
KL-ZE Swap - OBX SS Headers - 2.5" Exhaust - Falken Azenis Tires - H&R Springs - ZX-2 Struts - CAI - Front & Rear Tower Bar - AWR Motor Mounts - 100hp wet shot (yet to be tested)
Re: Front Main Oil Seal
your crank is harden to 60rc you won't scratch that unless your using a angle grinder or diamond filesElectricEnergy wrote:wont the screws scratch the hell out of the crankshaft/housing? Which part of the seal should I screw them into?
screw the screws into the flat of the seal as there is a steel band inside the seal, that what gives the
seal it's shape.
Re: Front Main Oil Seal
if you can go to princess auto and get a seal remover. it costs 3.99 cdn. it should work
95 rs with custom short ram air, b&m short throw shifter, probe 2.0L header with 2 1/4" exhaust all the way back, catco high flow cat, apc high flow muffler with 4.5" tip, accel 8 mm wires, blaze red, cf altezzas, gun metal 17" mr7s, slotted cross drilled rotors on the way with hawk hps pads, red and white interior, other then that its stock.
- ElectricEnergy
- Regular Member
- Posts: 489
- Joined: August 15th, 2006, 12:37 am
- Location: Saskatoon SK, Canada
Re: Front Main Oil Seal
so such a tool exists! I wish I had known before..... I'll go pick one up. Thanks a lot! I'll try the screws too.
KL-ZE Swap - OBX SS Headers - 2.5" Exhaust - Falken Azenis Tires - H&R Springs - ZX-2 Struts - CAI - Front & Rear Tower Bar - AWR Motor Mounts - 100hp wet shot (yet to be tested)
Re: Front Main Oil Seal
it looks like screw driver with a half moom shaped end on it. very handy tool.
95 rs with custom short ram air, b&m short throw shifter, probe 2.0L header with 2 1/4" exhaust all the way back, catco high flow cat, apc high flow muffler with 4.5" tip, accel 8 mm wires, blaze red, cf altezzas, gun metal 17" mr7s, slotted cross drilled rotors on the way with hawk hps pads, red and white interior, other then that its stock.
-
- Regular Member
- Posts: 31
- Joined: February 12th, 2008, 6:28 pm
Re: Front Main Oil Seal
get this tool
http://cgi.ebay.com/ebaymotors/SNAP-ON- ... enameZWDVW" onclick="window.open(this.href);return false;
http://cgi.ebay.com/ebaymotors/SNAP-ON- ... enameZWDVW" onclick="window.open(this.href);return false;
-
- Regular Member
- Posts: 217
- Joined: February 28th, 2006, 4:12 am
- Location: Saskatoon Sask, Canada
Re: Front Main Oil Seal
lol you guys are "to the MAX kind of people" .... its a seal... take a sharp little bent flat head screw driver and push it in and turn it to the side and PULL! lol.. done.
1993 Mazda MX-3 GS, V6 KLZE 2.5L, CenterForce Duel Friction Clutch, Nylon Shifter Bushings (from Imazda.com), Integra Cold Air Intake, Millenia Intake Manifold, Indigo Gauges, Pacesetter Header->Resonator->2.5" piping->Dynomax Muffler, VSX Front and back bumpers from FX Designs, AWR Front and back Motor Mounts.