i need money to finish my rx7 project
95 JDM Curvedneck KL-ZE 90,000kms
Swapped in KL-31 cams rebuilt and cleaned HLA's and Lifters
lightweight crank pulley
port & polished IM with knife edged behind TB
Accel performance HEI module
MSD blaster 3 coil
chipped KL-07 ECU
new mazda timing belt tensioner
this engine runs consistant low 14's
205psi of compression in all cylinders this is a strong engine
http://www.cardomain.com/member_pages/s ... 7_full.jpg
$1000
or $1400 installed
(FS) 95 modded KL-ZE engine
-
mazdaspeedmx_3
- Regular Member
- Posts: 151
- Joined: February 22nd, 2006, 3:41 pm
- Location: St. Thomas
(FS) 95 modded KL-ZE engine
2006 best ET 14.43 @ 96.9mph
93 MX-3 GS-95 Curveneck klze, kl-01 cammed,homemade CAI,HEI module, chipped kl-07 ECU,UDP,KYB GR-2 struts,DropZone lowering springs, Toyo Proxes 4's 205-50-r15
parts to be installed:Turbo hot pipes,T04E/t3 50/63 57 trim, ssqv BOV, hks style 38mm wastegate
the rest of my turbo set up and IPP hp rebuild kit is in the NEAR future
SOON TO BE MX-3ZE-T
93 MX-3 GS-95 Curveneck klze, kl-01 cammed,homemade CAI,HEI module, chipped kl-07 ECU,UDP,KYB GR-2 struts,DropZone lowering springs, Toyo Proxes 4's 205-50-r15
parts to be installed:Turbo hot pipes,T04E/t3 50/63 57 trim, ssqv BOV, hks style 38mm wastegate
the rest of my turbo set up and IPP hp rebuild kit is in the NEAR future
SOON TO BE MX-3ZE-T
-
Bling Bling
- Regular Member
- Posts: 1013
- Joined: January 5th, 2005, 10:27 pm
- Location: Airdrie, Alberta, Canada
Where is St. Thomas? Canada? hmmm lets's see what we could do....
Will it need anything or will I be able to just drop it in? And are there any signs of oil or coolant leaks?
Will it need anything or will I be able to just drop it in? And are there any signs of oil or coolant leaks?
Stacy Whitrick
MX-West Calgary
http://www.cardomain.com/ride/1335558 UPDATED June 6,07
94 GS, Green Envy Pearl QUESTION: Does my car fit the RICE category?
MX-West Calgary
http://www.cardomain.com/ride/1335558 UPDATED June 6,07
94 GS, Green Envy Pearl QUESTION: Does my car fit the RICE category?
-
mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
wish it was closer
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks
http://www.cardomain.com/id/mitmaks
-
mazdaspeedmx_3
- Regular Member
- Posts: 151
- Joined: February 22nd, 2006, 3:41 pm
- Location: St. Thomas
i put a new water pump on it last year,,,theres no leaks whatsoever on the engine
just bolt it down plug it in and go
just bolt it down plug it in and go
2006 best ET 14.43 @ 96.9mph
93 MX-3 GS-95 Curveneck klze, kl-01 cammed,homemade CAI,HEI module, chipped kl-07 ECU,UDP,KYB GR-2 struts,DropZone lowering springs, Toyo Proxes 4's 205-50-r15
parts to be installed:Turbo hot pipes,T04E/t3 50/63 57 trim, ssqv BOV, hks style 38mm wastegate
the rest of my turbo set up and IPP hp rebuild kit is in the NEAR future
SOON TO BE MX-3ZE-T
93 MX-3 GS-95 Curveneck klze, kl-01 cammed,homemade CAI,HEI module, chipped kl-07 ECU,UDP,KYB GR-2 struts,DropZone lowering springs, Toyo Proxes 4's 205-50-r15
parts to be installed:Turbo hot pipes,T04E/t3 50/63 57 trim, ssqv BOV, hks style 38mm wastegate
the rest of my turbo set up and IPP hp rebuild kit is in the NEAR future
SOON TO BE MX-3ZE-T