[FS] Parting out modded 1994 RS ????

projectmx · Post by **projectmx** » June 26th, 2007, 10:39 am

I have a 1994 white RS that i'm parting out.. I only have about 2-3 weeks to do this maybe a little longer but not much.

It is white pics can be seen at my cardomain page: http://www.cardomain.com/id/projectmx

Here is the aftermarket stuff i'm selling:
Shaved doors (i might keep these but if the price is right i'll sell)
Door popper kit (if i sell the doors this will come with since it's already installed)
Black Integra intake
Header back exhaust (has a few dings but worked great when i was driving the car around)
GS spoiler
SRD Control arm bushings
Front control arms (sandblasted and repainted last summer)

Pretty much everything is for sale off of it I do want to keep some parts but i might even sells those of the offer is right. I really really need to get this car gone and get the last bit of money to get my AWD mx-3 done so please please please help me

I'm posting this here on clubprotege and feoa.net if anyone comes down and pulls parts off themselves I will charge less.. I can also bring some parts up to the chicago area with me if anyone needs anything and doesn't want to drive down to the kankakee area

The bad parts on the car as as follows:
Rear end was hit so rear bumper is gone and bumper support
the small shifter linkage part that is in the trans is bent and needs to be replaced to shift right
as far as i know everything else works great on the car.

let me know if you need anything and i'll try and get it for you.
engine runs great also and had a new water pump and timing belt put in last year also has a new clutch as of last year

Vanished · Post by **Vanished** » June 26th, 2007, 3:01 pm

Hey I want the SRD bushings. 50 bucks plus shipping?

projectmx · Post by **projectmx** » June 26th, 2007, 3:04 pm

uhm i think i paid over $120 for those brand new and they only have 6 months use on them. I have them listed as $90 plus shipping on clubprotege .... i'd be willing to do $70 plus shipping but no less

Tunes67 · Post by **Tunes67** » June 26th, 2007, 3:08 pm

Do you have or are you willing to sell any interior panels? I need the panels (both upper & lower) behind the doors. On either side of the rear seat. If they are in ok shape and you want to sell them.. how much would you charge? They should lay fairly flat so shipping shouldnt be too bad.

Tunes67

projectmx · Post by **projectmx** » June 26th, 2007, 3:28 pm

do you mean the sort of arm rest things for the rear seat passengers?

Tunes67 · Post by **Tunes67** » June 26th, 2007, 3:31 pm

The whole panel and the smaller panel that the seat belt clip bolts through thats above the larger lower panel. And I need them from both sides of the car. Need to have the rear seats out to remove them too :S I can take pics of them if you need for positive identification

Tunes67

Tunes67 · Post by **Tunes67** » June 26th, 2007, 4:43 pm

These panels LOL Thanks for the pic Killerpickle

Tunes67

TEAMpK · Post by **TEAMpK** » June 26th, 2007, 4:59 pm

How about the bottom end or entire motor?

Post by **Custommx3** » June 26th, 2007, 5:11 pm

Please fix the topic.

PATDIESEL · Post by **PATDIESEL** » June 26th, 2007, 7:42 pm

Tunes, those panels look flat, but once you get them out you'll see that they have fairly long guide pins molded into the back to line them up when installing them. Might be a larger package than you think.

I am looking for the door seals. Need to be in exceptional shape for the age. specifically-
1. belt trim (outside and inside part that touches the window, must have good felt on them still and must not be bent when removing)(the interior belt trim is attached to the door panel, but I only want the seal),
2. door seal (the part that keeps water and air out when you close the door, the clips would be nice too, but are prone to break when you remove the seal),
3. little rubber trim on the upper door edge (closes the gap between the door and body panels for a clean look, I don't think they acutally serve a purpose).
4. I also need the plasic caps that go over the bolts on the wiper cowl cover. Please PM with prices incase I miss reading a reply on here.
Thanks,
Patrick

Tunes67 · Post by **Tunes67** » June 26th, 2007, 7:52 pm

Yeah but even if the package is a bit large.. it wont weigh much.. so the shipping on it should still be reasonable.

Tunes67

PATDIESEL · Post by **PATDIESEL** » June 27th, 2007, 12:17 am

Its about the size of the ocean not its weight little brotha.

projectmx · Post by **projectmx** » June 27th, 2007, 8:16 am

lol pat that was so wrong

panels should be in good condition but i'll check them out friday when i pick up my car

team pk... engine is yours if you want. i'd like $250 plus shipping or depending on where you live I could work out bring it or meeting half way

pat i'm not sure about all those seals.... i think they aren't in good condition especially the door ones cause i had to break into the car once. are they not available through mazda or just too much? i'll look them over fri/sat

projectmx · Post by **projectmx** » June 28th, 2007, 11:32 am

tunes is 30 plus shipping ok for the panels if they are in good shape? pm me and we'll try and work out the details

projectmx · Post by **projectmx** » June 28th, 2007, 11:48 am

if anyone lives near me don't forget if you want to come strip parts off i'll charge less and if you come help with the the AWD mx-3 there's a good chance i'll throw free parts in for ya

i realllllly want to get my car up and running