MechaManZero - 1995 MX3 BPD GTR *UPDATED PICS 8/14/06*
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
MechaManZero - 1995 MX3 BPD GTR *UPDATED PICS 8/14/06*
Here are some pictures of before I dropped the engine in my car
Lol well the rust can be takin care of but I will save up for the total paint job and restoration after the motor is running and my exhaust setup is done.
The situation: Dropped in the BPT. The 95 MX-3 is a pain with wiring harnesses and found that the gtx was a direct fit with the 93 MX3, hoping it would cut corners with the gtr engine that I put in. Well Problem number one that I bumped into was the TPS being changed from a 3 plug to a 4 plug. Due to another wire needng to be hooked up from the VAF this was no problem afterwards. Now the real pain comes. The fuel harness. Well on the BPs it seems that 2 injectors fire at the same time (why they do this makes no sense if you don't believe me check out the wiring diagrams.). So the only wires that really matched where the yellow which ran cylinder 1 and 3 and the yellow with a black stripe which ran cylinder 2 and 4. From here all of the wires are completely different colors. Also I am going from an 8 plug to a 9 plug on the gtr. Pretty freaky. I will update pics soon.
Lol well the rust can be takin care of but I will save up for the total paint job and restoration after the motor is running and my exhaust setup is done.
The situation: Dropped in the BPT. The 95 MX-3 is a pain with wiring harnesses and found that the gtx was a direct fit with the 93 MX3, hoping it would cut corners with the gtr engine that I put in. Well Problem number one that I bumped into was the TPS being changed from a 3 plug to a 4 plug. Due to another wire needng to be hooked up from the VAF this was no problem afterwards. Now the real pain comes. The fuel harness. Well on the BPs it seems that 2 injectors fire at the same time (why they do this makes no sense if you don't believe me check out the wiring diagrams.). So the only wires that really matched where the yellow which ran cylinder 1 and 3 and the yellow with a black stripe which ran cylinder 2 and 4. From here all of the wires are completely different colors. Also I am going from an 8 plug to a 9 plug on the gtr. Pretty freaky. I will update pics soon.
Last edited by MechaManZero on August 16th, 2006, 8:29 am, edited 3 times in total.
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
OK Besides being sunblind today LMAO, here are the results of the harness so far
6/9 wires found out
Cylinder 1 injector
Yellow - Supposably going to ECU
Pink - Supposably the injector Relay
Cylinder 2 injector
Yellow + Black Stripe - Supposably going to ECU
Red - Supposably the injector Relay
Cylinder 3 injector
Yellow - Supposably going to ECU
Purple - Supposably the injector Relay
Cylinder 4 injector
Yellow + Black Stripe - Supposably going to ECU
Orange - Supposably the injector Relay
Searching for what the other wires are for now
6/9 wires found out
Cylinder 1 injector
Yellow - Supposably going to ECU
Pink - Supposably the injector Relay
Cylinder 2 injector
Yellow + Black Stripe - Supposably going to ECU
Red - Supposably the injector Relay
Cylinder 3 injector
Yellow - Supposably going to ECU
Purple - Supposably the injector Relay
Cylinder 4 injector
Yellow + Black Stripe - Supposably going to ECU
Orange - Supposably the injector Relay
Searching for what the other wires are for now
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
Ok so I had the six wires before, come to find out the other wires are clearly connected to the sensors in front and behind the thermostat housing. Blue and white and two black w/ brown stripes. Whole harness on the gtr figured out.
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
J-SPEC FUEL HARNESS
Cylinder 1 injector
Yellow - ECU
Pink - Resistor
Cylinder 2 injector
Yellow + Black Stripe - ECU
Red - Resistor
Cylinder 3 injector
Yellow - ECU
Purple - Resistor
Cylinder 4 injector
Yellow + Black Stripe - ECU
Orange - Resistor
Coolant Temperature Sensor
Blue + White Stripe - ECU
Black + Brown - Ground
Coolant Temperature Sender
Black + Orange - Instrument Cluster
NOTE: The yellow wire on cylinder one and three injectors are merged as well as the yellow + black for cylinder 2 and 4 injectors seeing that the BP series ECU grounds out two cylinders at a time.
NOTE: Also the harness is not the same as a GTR from the UK.
Cylinder 1 injector
Yellow - ECU
Pink - Resistor
Cylinder 2 injector
Yellow + Black Stripe - ECU
Red - Resistor
Cylinder 3 injector
Yellow - ECU
Purple - Resistor
Cylinder 4 injector
Yellow + Black Stripe - ECU
Orange - Resistor
Coolant Temperature Sensor
Blue + White Stripe - ECU
Black + Brown - Ground
Coolant Temperature Sender
Black + Orange - Instrument Cluster
NOTE: The yellow wire on cylinder one and three injectors are merged as well as the yellow + black for cylinder 2 and 4 injectors seeing that the BP series ECU grounds out two cylinders at a time.
NOTE: Also the harness is not the same as a GTR from the UK.
Last edited by MechaManZero on July 31st, 2006, 11:16 pm, edited 2 times in total.
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
good info
1994, GS, KLZE, 67mm TB, LightFlywheel, Centreforce Stg 3 Clutch, CAI, KL36 ecu, B&M shortshifter, Solid poly mounts, lightweight Aluminum Cross memeber, 2.5 high flo cat, 2.5 all back, Tanabe Exhaust, optima battery, ZX2 HD tokicos, eibach prokit, black altezzas.....
http://www.modifiedmazda.com" onclick="window.open(this.href);return false;.
http://www.modifiedmazda.com" onclick="window.open(this.href);return false;.
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
I have been running into some good deals so if you guys want I can pinout most of the clips, except for distributor and VAF... They are the same.
Hopefully if I get the ECU and Wiring Loom I will take a picture of that and the motor in the car.
Hopefully if I get the ECU and Wiring Loom I will take a picture of that and the motor in the car.
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
If anyone needs to know any good information with this swap talk to the crew at http://www.323gtx.co.uk
They have been helping me here in there. They are all good at this cause the UK has GTRs and GTXs.
NOTE: The J-Spec GTR has a different fuel pressure regulator than the Euro-Spec GTR.
They have been helping me here in there. They are all good at this cause the UK has GTRs and GTXs.
NOTE: The J-Spec GTR has a different fuel pressure regulator than the Euro-Spec GTR.
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
Well its been two months, I just bought axles yesterday, I think I might have found a jack shaft and need it dearly. ECU and harness comes in on the 13 i think.
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
Intermediate shaft is coming on tuesday. I have the axles. I am putting new wheel bearing and rotors in. Getting the J-Spec Harness and ECU on the 14th supposably. Lets see how things go.
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
NEW PICS
Basically I have the piping temp on to fit everything till I get my BOV and pipe with a flange but looks pretty good so far. Intercooler is proped up until my visit at home depot and than I shall have pics up of the Intercooler where it should be. Minor hack job on the bumper for now. Thanks to my neighbor Justin all of this is possible without me breaking stuff with an extra hand.
Basically I have the piping temp on to fit everything till I get my BOV and pipe with a flange but looks pretty good so far. Intercooler is proped up until my visit at home depot and than I shall have pics up of the Intercooler where it should be. Minor hack job on the bumper for now. Thanks to my neighbor Justin all of this is possible without me breaking stuff with an extra hand.
Last edited by MechaManZero on June 27th, 2018, 9:54 am, edited 1 time in total.
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
Its amazing. New ball joints, tie rod ends and wheel bearings. The wheels are on and I am sporting some ceramics for brakes .
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
I shall be paying for the GTR ECU and wiring harness from corksport tomorrow yeay. I will update when it comes in next week.
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
Well damn its been long since I updated this. I got the ECU and wiring harness and hopefully I will be able to start it in two weeks or three depending on the mony situation. But it shall be sick when it is done. i have to relocate my battery still. I also have to figure out what I am going to do with the radiator situation. I was thinkin stick with stock for now and change my pipe setup.
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
If you want to put a slimmer radiator for a same side intercooler like me, I found out an 88 Honda CRX Radiator fits just fine. Got one the other day, test fit it and saw room for 2.5 inch pipes on the side. 1337
Çlark
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/