speed limiter?
- !vetc-this!
- Junior Member
- Posts: 24
- Joined: March 19th, 2006, 7:16 pm
speed limiter?
I installed my j-spec ecu earlier this week and today went for a top speed run and at about 115 the car sputtered real bad (scared the s--- out of me I thought I blew it up) so slowed down and accelerated again (not up to 115)and all was fine any one any ideas ? iam affraid to try again
- relisys_3200
- Regular Member
- Posts: 875
- Joined: November 11th, 2004, 2:01 am
- Location: London / Ontario / Canada
- Contact:
- !vetc-this!
- Junior Member
- Posts: 24
- Joined: March 19th, 2006, 7:16 pm
- Nd4SpdSe
- Senior Member
- Posts: 11212
- Joined: May 25th, 2002, 2:01 am
- Location: Québec City, Quebec, Canada
- Contact:
My KL36 supposibly had a speed limiter, but Lazzyie removed it. Kp2t has a KL36 ECU I believe, and it has a limiter around 180-190 Km/h.
It should be removable by cutting the "Speedometer To ECU" wire listed in the Online Shop manual, but I don't know of anyone who has tried it.
It should be removable by cutting the "Speedometer To ECU" wire listed in the Online Shop manual, but I don't know of anyone who has tried it.
1992 Mazda Mx-3 GSR - 2.5L KLZE : Award Winning Show Car & Race Car ['02-'09] (Retired)
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
- relisys_3200
- Regular Member
- Posts: 875
- Joined: November 11th, 2004, 2:01 am
- Location: London / Ontario / Canada
- Contact:
- Nd4SpdSe
- Senior Member
- Posts: 11212
- Joined: May 25th, 2002, 2:01 am
- Location: Québec City, Quebec, Canada
- Contact:
Yep, that's the one, Shop Manual page F2-144/145. 1M Vehicle Speed Sensor.
1992 Mazda Mx-3 GSR - 2.5L KLZE : Award Winning Show Car & Race Car ['02-'09] (Retired)
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
- !vetc-this!
- Junior Member
- Posts: 24
- Joined: March 19th, 2006, 7:16 pm
- Nd4SpdSe
- Senior Member
- Posts: 11212
- Joined: May 25th, 2002, 2:01 am
- Location: Québec City, Quebec, Canada
- Contact:
The diagram I believe says Green/Red, but the marking 1M should be on the ECU.
1992 Mazda Mx-3 GSR - 2.5L KLZE : Award Winning Show Car & Race Car ['02-'09] (Retired)
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
-
- Senior Member
- Posts: 6451
- Joined: June 19th, 2004, 2:01 am
- Location: El Paso Tx U.S
- Contact:
AAA THATS THE BP engine..says B8 .... not k8relisys_3200 wrote:to remove my limiter, I did this..
Cut that wire It is coming out of the medium sized (22 wires) plug going into your ECU and the diagram is as if you were looking into the plugs on the ECU (wires are coming towards you).
-hec
MX-3 w/ curved neck millenia klde, boosted @ 5 psi. /bov and wastegate are good!/ nitto drag radial/ gutted interior/ millenia red top injectors, vortech fmu/aem wideband/ all bolts ons/ Car put together 100% by me. Mechanic? who needs a mechanic? ew.. real men work on their own cars!
MX-3 w/ curved neck millenia klde, boosted @ 5 psi. /bov and wastegate are good!/ nitto drag radial/ gutted interior/ millenia red top injectors, vortech fmu/aem wideband/ all bolts ons/ Car put together 100% by me. Mechanic? who needs a mechanic? ew.. real men work on their own cars!
- Nd4SpdSe
- Senior Member
- Posts: 11212
- Joined: May 25th, 2002, 2:01 am
- Location: Québec City, Quebec, Canada
- Contact:
You may be right, but it's still 1M. Check the online manual F2-148
http://www.mx-3.com/95manual/page.cfm?S ... PageNo=148
http://www.mx-3.com/95manual/page.cfm?S ... PageNo=148
1992 Mazda Mx-3 GSR - 2.5L KLZE : Award Winning Show Car & Race Car ['02-'09] (Retired)
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
- relisys_3200
- Regular Member
- Posts: 875
- Joined: November 11th, 2004, 2:01 am
- Location: London / Ontario / Canada
- Contact:
Yeah KL-36 cuts at ~115 mph.
I don't remember the pin number i cut on my 1993 MX-3 GS, but it removed the speed limiter completely and no CEL, or ill effects..
But i remeber the wire being way smaller gauge then the rest and i think mine was black and white. I'll get back to you on that.
I don't remember the pin number i cut on my 1993 MX-3 GS, but it removed the speed limiter completely and no CEL, or ill effects..
But i remeber the wire being way smaller gauge then the rest and i think mine was black and white. I'll get back to you on that.
***D-Tuned Custom KL MX-3 on Nitrous***