I did a search but couldn't find anything about the actualy wiring of the KLZE EGR valve. The solonoids and vacuum hoses are easy to hook up, but the K8 EGR VALVE wire connector clip and the KLZE EGR VALVE wire connector clip are different.. Here is a pic of the KLZE EGR valve (left) and the K8 EGR valve SENSOR (right) - (same part from both)
http://www.mkd.cc/egrwireing.jpg
(If this doesn't load copy/paste the address into a new browser window and reload it.. sorry...)
I tried using a Ohms tester to check to see if the wires were configured the same way by trying differnet 3-prong combinations while pressing the internal EGR switch (the K8's is visible on the right) with my finger. I had no constand results... Does anybody know if I can just splice the K8's wire and solder/clip the wires onto the KLZE connector in the same physical order..? Thanks for the help!
KLZE EGR wireing help
-
- Regular Member
- Posts: 540
- Joined: May 23rd, 2003, 2:01 am
- Location: Placerville, California
- Contact:
KLZE EGR wireing help
![Image](http://i95.photobucket.com/albums/l129/oursdekoala/avatar_nov3.jpg)
GS-R SE
Fixin's
-
- Forum Moderator
- Posts: 3415
- Joined: September 3rd, 2002, 2:01 am
- Location: Eastern Hemisphere
- Contact:
Re: KLZE EGR wireing help
klze egr? ive seen a few klzes and ive never seen one with an egr
08 Infiniti G37s 6speed (The Daily)
Stillen Cold Air Intake, Z1 Plenum Power Mod, Z1 Headers, Z1 Test Pipe, OBX (Ark) Exhaust, Up-Rev Osiris Engine Management (Tuned at Z1), 20x9" 20x10" Str Racing Concave Staggered Rims, SPC Camber kit, Tein H Techs Springs
01 Lexus Is300 (LS2 Project)
93 Mx3 SE 2.5 KLZE (sold it)
93 Mx3 GS 2.0 KFZE (killed it)
Stillen Cold Air Intake, Z1 Plenum Power Mod, Z1 Headers, Z1 Test Pipe, OBX (Ark) Exhaust, Up-Rev Osiris Engine Management (Tuned at Z1), 20x9" 20x10" Str Racing Concave Staggered Rims, SPC Camber kit, Tein H Techs Springs
01 Lexus Is300 (LS2 Project)
93 Mx3 SE 2.5 KLZE (sold it)
93 Mx3 GS 2.0 KFZE (killed it)
-
- Regular Member
- Posts: 1179
- Joined: August 27th, 2001, 2:01 am
- Location: Russellville, AR, USA
Re: KLZE EGR wireing help
Snip off the K8 connector, solder on some female bayonet type connectors and stick them on directly. Cover it up with tape.
KLZE, ZE PCM, UR pulley, PS catback, PS STS, PRM, IAC bypass, 64mm TB, FOP hair gel
-
- Regular Member
- Posts: 540
- Joined: May 23rd, 2003, 2:01 am
- Location: Placerville, California
- Contact:
Re: KLZE EGR wireing help
Ahh, I was hoping I could just do that.. So you're sure I can just use the same order?
![Image](http://i95.photobucket.com/albums/l129/oursdekoala/avatar_nov3.jpg)
GS-R SE
Fixin's
-
- Regular Member
- Posts: 1179
- Joined: August 27th, 2001, 2:01 am
- Location: Russellville, AR, USA
Re: KLZE EGR wireing help
That is what I would be doing if I had your problem.
KLZE, ZE PCM, UR pulley, PS catback, PS STS, PRM, IAC bypass, 64mm TB, FOP hair gel
-
- Regular Member
- Posts: 909
- Joined: March 15th, 2004, 2:01 am
- Location: Karlskrona, Sweden
- Contact:
Re: KLZE EGR wireing help
How did it go? Did you fix the connector?
-
- Regular Member
- Posts: 540
- Joined: May 23rd, 2003, 2:01 am
- Location: Placerville, California
- Contact:
Re: KLZE EGR wireing help
Hey. Everything is ready, but I'm in the middle of rebuilding a tranny... Bookmark this and I will reply within a month with my smog test results ![Wink ;)](./images/smilies/icon_wink.gif)
![Wink ;)](./images/smilies/icon_wink.gif)
![Image](http://i95.photobucket.com/albums/l129/oursdekoala/avatar_nov3.jpg)
GS-R SE
Fixin's