klze with k8ecu
-
- Regular Member
- Posts: 486
- Joined: July 16th, 2002, 2:01 am
- Location: canada
klze with k8ecu
im told my interals will fry by a local mechanic. is it safe to drive on it for like 2 weeks>?
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
Re: klze with k8ecu
its gonna run super rich, see if you can track down a MX-6 or Probe GT VAF, that will run decent from what im told
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
-
- Regular Member
- Posts: 45
- Joined: August 24th, 2003, 2:01 am
- Location: san diego
Re: klze with k8ecu
I'm Currently Running an mx-6 ecu until corksport can send me my klze ecu. But The only thing that i've noticed is that the timing in lower rpm's isn't exact and can seem a bit sluggish at times but over all it works and i don't get that bad of gas mileage out of it.
Wha-hoooo!!!! its finally in pics to come soon. http://www.cardomain.com/memberpage/540890
-
- Regular Member
- Posts: 733
- Joined: January 16th, 2001, 2:01 am
- Location: Niagara Falls, Canada
- Contact:
Re: klze with k8ecu
which vaf are you using with the mx6 one? You have to use the 2.5 vaf. The 1.8 will throw codes and run like garbage.
Tom Alexander
93 MX3 GSR - KLZE / stage 3 clutch / PRM Intake / 2.25" exhaust - dual 3" outlet
full custom black and red interior / KLZE ECU / JE50 VAF
http://home.cogeco.ca/~mx3/ - updated dec 1/03
93 MX3 GSR - KLZE / stage 3 clutch / PRM Intake / 2.25" exhaust - dual 3" outlet
full custom black and red interior / KLZE ECU / JE50 VAF
http://home.cogeco.ca/~mx3/ - updated dec 1/03
-
- Regular Member
- Posts: 528
- Joined: January 23rd, 2004, 2:01 am
- Location: East Grand Forks, MN
Re: klze with k8ecu
I'm running a K8 ecu and a 2.5Ltr VAF, it runs alot better with that VAF than the K8 VAF. Lots better gas mileage and smoother running.
THIS USER HAS BEEN BANNED, DO NOT DEAL WITH HIM. - MX-3.com Admin
-
- Regular Member
- Posts: 45
- Joined: August 24th, 2003, 2:01 am
- Location: san diego
Re: klze with k8ecu
I'm Still running the stock k8 vaf and i'm not throwing any codes no problems other than previously stated.
Wha-hoooo!!!! its finally in pics to come soon. http://www.cardomain.com/memberpage/540890
-
- Regular Member
- Posts: 733
- Joined: January 16th, 2001, 2:01 am
- Location: Niagara Falls, Canada
- Contact:
Re: klze with k8ecu
the mx6 ecu and the 1.8 vaf do not go well together, trust me
Tom Alexander
93 MX3 GSR - KLZE / stage 3 clutch / PRM Intake / 2.25" exhaust - dual 3" outlet
full custom black and red interior / KLZE ECU / JE50 VAF
http://home.cogeco.ca/~mx3/ - updated dec 1/03
93 MX3 GSR - KLZE / stage 3 clutch / PRM Intake / 2.25" exhaust - dual 3" outlet
full custom black and red interior / KLZE ECU / JE50 VAF
http://home.cogeco.ca/~mx3/ - updated dec 1/03