MX-3.com

my mini get it back on the road project included completing some minor upgrades.

I had been sitting on the parts for a long time. I installed a set of Exile Autoworx supplied cam covers in wrinkle red with all new gaskets and bolt hardware. The quality of his work is just outstanding.

https ...

Back on the road again after three years in the shed. Big clean up under the hood, different manifold etc.

https://www.supermotors.net/getfile/1172390/fullsize/img_9740.jpeg

https://www.supermotors.net/getfile/1172389/fullsize/img_9739.jpeg

The roadworthy test failed the car on the front ...

Bosch combined temperature and 10 Bar fluid pressure sensor and thread adapter (NPT)

https://www.supermotors.net/getfile/1172384/fullsize/img_9953.jpeg

https://www.supermotors.net/getfile/1172385/fullsize/img_9955.jpeg

https://www.supermotors.net/getfile/1172386/fullsize/img_9954.jpeg ...

Hi Craig. Still a live project I confess. I broke it about 2 years ago. I have just got back to it now that I have a little more time. I had a problem with the injectors. Poor running and a lot of frustration. Left it to gather dust in the shed. I have a fully refurbished long neck ZE manifold, with ...

Indeed

Me too!!

Very quiet here which is sad,

Just doodling a bit here.

Currently fitted with Mazda Lantis knuckles, 5 stud hubs, rotors and brake calipers and brackets.

https://www.supermotors.net/getfile/1168011/fullsize/img_7500.jpeg

https://www.supermotors.net/getfile/1168012/fullsize/img_7501.jpeg

https://www.supermotors.net ...

Bump :D

I'll be updating this soon for the 11 people that still visit this board and the 3 that will actually read this post..... :lol: :lol:



Hi. Greetings from 1 of the 3. Great to see this post and your subsequent ones. Congratulations on the quality of the work. Keep the posts coming ...

I have made a trial fit of a set of lateral locks to the Whiteline rear sway bar .

https://www.supermotors.net/getfile/1161458/fullsize/img_5893.jpg

The locks are fitted in pairs. I am using the KLL122 kit.

https://www.supermotors.net/getfile/1161454/fullsize/img_5889.jpg

https://www ...

Swapped in a FullRiver HC 20 lightweight absorbent glass mat (AGM) based battery.

https://www.batteriesdirect.com.au/shop/product/22715/fullriver-high-cranking-battery.html

I was running one of these

http://www.exidebatteries.co.nz/battery-range/passenger/extreme/x55d23cmf

Less than half the ...

Hi.

I am glad you found us here. Not much day to day activity these days but perhaps the accumulated posts are of some use.

Good luck with your project with your grandson.

Chris

Ok back to the job I really want to finish. Had to refit all the interior trim removed to fit the spoiler. Lots of mucking around for little to show.

I want to get on with the many silly little things so that I can make the engine and transaxle swap.

I want to make sure that the silly stuff doesn ...

Its getting confusing with two project themes all mixed up in the one Project thread. The Presso are both shades of red (sort of), both 1993 models and both K8’s (originally).

To distinguish the two apart I have taken to using their build serial numbers as a quick way of separating them.

The cars ...

I have gone mad and cleaned up the shed.

The day time temperatures in the shed are about 30 Celcius (for a big part of the day) here at the minute.

However there is a method in my madness.

I need to complete the KLZE/transaxle swap on the red car ASAP. All the many bits and parts have been ...

want to try this;

1989 1990 1991 FC3S Mazda Rx7 Master Power Window Switch F06166350A.

Its almost a twin for the bargin bin JDM Eunos Presso standard fit out.

https://www.supermotors.net/getfile/1144276/fullsize/p1080571.jpg

https://www.supermotors.net/getfile/1144277/fullsize/p1080572.jpg ...

Tested the spark to Cylinder #6. Big fat hot spark shown in the tester while the engine was running. That was enough for me. Swapped out the in-place fuel rails as a set.

Swapped in the fuel rail set that were fitted to the original MX-6 engine (KLZE straight neck). The set has been sitting on the ...