MX-3.com

yes i sprayed some carb cleaner on the outside of the tubing where it looked cracked and i didnt notice any revving. I had my air conditioning on today when i was waiting at a light and it seemed like it was missing a cylinder every second. It was really bad, almost like my car wanted to stall. The ...

I was way off..i have a 1.6 manual trans. right when i start the car it idles at around 800 and when at normal operating temp ts about 600. I also tried to pull the codes. The check engine light came on in the beginning and then went off and stayed off which i thought meant there were no code stored...

check for a vacuum leak. 1500 is way too high, my car idles a little over 600. what motor are you using? how to check codes: http://www.mx-3.com/phpBB3/viewtopic.php?f=23&t=64675&view=previous" onclick="window.open(this.href);return false; maybe im making a mistake with those numb...

fowljesse wrote:A full tune-up wouldn't hurt. Or at least check everything out.
Check the codes, and see if there's something there. What rpm does it idle at?

I have no CEL, i didnt know i could pull codes without a light?? hmm. It idles around 1.5k give or take a little.thanks

Hey all. When I m driving, sometimes my car spudders when i am driving slower in a gear. Maybe 15 mph in 2nd, 22-27 in 3rd, and so on. Also it does it when im idleing as well. Almost like im missing a cylinder. It happened a while ago and i changed the plugs and wires and it went away but now its ba...

RS_OBD'oh_2 wrote:looks like it does not have enough of a bend.. but for under 20.00 just try it. Not a loss if you have to buy a few.

Yea I was afraid of the bend problem

How about these ones?! They look similar to the probe ones http://cgi.ebay.com/ebaymotors/99-00-HONDA-CIVIC-EX-SI-SHORT-AIR-INTAKE-SYSTEM-FILTER-_W0QQcmdZViewItemQQhashZitem27b19db193QQitemZ170483626387QQptZMotorsQ5fCarQ5fTruckQ5fPartsQ5fAccessories" onclick="window.open(this.href);return ...

this is done to death!!! Please search again. None of those are any good. You need 3 nipples for the best fit, they will also need to be located near the elbow off the TB. I don't understand what you are saying about the MAF.... you don't need a hole for it... it fits in line... being the CAI is a ...

this is done to death!!! Please search again. None of those are any good. You need 3 nipples for the best fit, they will also need to be located near the elbow off the TB. I don't understand what you are saying about the MAF.... you don't need a hole for it... it fits in line... being the CAI is a ...

Why did you make two of the same posts? It's annoying... delete one. Anyhow, I'm looking at doing this soon as well. I'm a '96 B6DE, so same thing. There are Integra kits with 2 or 3 nipples. Keep lookin... And don't forget you can always add nipples if you need, or just use breathers on the hoses....

Im looking to get an intake for my 1995 1.6 dohc. I know there are thousands of posts on this but I have searched for the past few days and havent had my questions really answered. I noticed that I could possibly use an integra intake with some modification. Some of them that ive seen only have one ...

ok after a home made funnel and a little time, i was finally done. Put the speedo gear back on and drove her a little. Seems to be much better going from 1st to 2nd now but 3rd to 4th is worse. All in all i would rate the shifting worse now than it was but not by much, just expected better. Ive only...

Ok Ive run into some problems. I looked at everyones responses and thought i had a good idea what to do. I went to look in the manual to locate the speedo cable where i would fill the fluid and nothing is there. Also Im assuming that the giant bolt on the bottom of the trans is what im supposed to t...

Yes I just did a simple search and found out that there is no filter, dumb on my part. Thanks. I spoke to someone and they said to use a GL4 fluid because of the brass synchros and to use Redline MT90. Does this make sense? Anyone also use this? Thanks again

Im seeing some info on changing a filter for the transmission? And also a pan gasket. Should I change these as well? Thanks