well since ebay can be kind of unsafe i was wondering if anyone had used anything from this place
http://stores.ebay.com/Aimco-Clutch-Co
Ebay clutch and flywheel
-
MazdaNoob123
- Regular Member
- Posts: 187
- Joined: October 12th, 2005, 2:09 pm
- Location: Bellingham, WA
Ebay clutch and flywheel
I still cant find anywhere in the shop manual where it says there should be a 1in hole in the side of the block. (Blown K8) #6 rod thrown through block.
i have an XTD stage 2 clutch off ebay... it's not bad. pressure plate feels a lil too soft, but a thing like that is personal preference. main thing is it grips well and it's lasted, though i hardly ever beat on it. i think i might even have bought it from that exact seller. with that many feedbacks you're sure not to get scammed, but big sellers like that can be hard to communicate with as well
-
hgallegos915
- Senior Member
- Posts: 6451
- Joined: June 19th, 2004, 2:01 am
- Location: El Paso Tx U.S
- Contact:
hmm wow 500 dllrs :S for that kind of money you can get a FIDANZA fly and a gripforce clutch, it grabs HARD but it will only last about a year or so.(depending on your driving)
They are meant to "feel and act" like a stage 3 but last less.
It was a good bang for the buck imo before i upgrade.
The fidanza wakes up the engine a bit good
They are meant to "feel and act" like a stage 3 but last less.
It was a good bang for the buck imo before i upgrade.
The fidanza wakes up the engine a bit good
-hec
MX-3 w/ curved neck millenia klde, boosted @ 5 psi. /bov and wastegate are good!/ nitto drag radial/ gutted interior/ millenia red top injectors, vortech fmu/aem wideband/ all bolts ons/ Car put together 100% by me. Mechanic? who needs a mechanic? ew.. real men work on their own cars!
MX-3 w/ curved neck millenia klde, boosted @ 5 psi. /bov and wastegate are good!/ nitto drag radial/ gutted interior/ millenia red top injectors, vortech fmu/aem wideband/ all bolts ons/ Car put together 100% by me. Mechanic? who needs a mechanic? ew.. real men work on their own cars!
-
MazdaNoob123
- Regular Member
- Posts: 187
- Joined: October 12th, 2005, 2:09 pm
- Location: Bellingham, WA
http://cgi.ebay.com/ebaymotors/XTD-STAG ... QQtcZphoto
349 with a 9lb flywheel
349 with a 9lb flywheel
I still cant find anywhere in the shop manual where it says there should be a 1in hole in the side of the block. (Blown K8) #6 rod thrown through block.
-
Mnemonic
- Forum Moderator
- Posts: 3415
- Joined: September 3rd, 2002, 2:01 am
- Location: Eastern Hemisphere
- Contact:
the clutch may be good but i dunno about the flywheel, looks similar to fidanzas flywheel just minus the ability to replace the surface ring, so in the end you would have to replace this entire flywheel, unlike with the fidanza where you pay 50 bucks to replace the surface ring.
08 Infiniti G37s 6speed (The Daily)
Stillen Cold Air Intake, Z1 Plenum Power Mod, Z1 Headers, Z1 Test Pipe, OBX (Ark) Exhaust, Up-Rev Osiris Engine Management (Tuned at Z1), 20x9" 20x10" Str Racing Concave Staggered Rims, SPC Camber kit, Tein H Techs Springs
01 Lexus Is300 (LS2 Project)
93 Mx3 SE 2.5 KLZE (sold it)
93 Mx3 GS 2.0 KFZE (killed it)
Stillen Cold Air Intake, Z1 Plenum Power Mod, Z1 Headers, Z1 Test Pipe, OBX (Ark) Exhaust, Up-Rev Osiris Engine Management (Tuned at Z1), 20x9" 20x10" Str Racing Concave Staggered Rims, SPC Camber kit, Tein H Techs Springs
01 Lexus Is300 (LS2 Project)
93 Mx3 SE 2.5 KLZE (sold it)
93 Mx3 GS 2.0 KFZE (killed it)