Problems with fuel management install
Problems with fuel management install
got some Questions
what dose each wire do on the 4 wire tps off an auto(92-93)
what dose each wire do on the Distributor (theres 3)
is it ok to hook up a msd and my megasquirt all to the ignition switch
and can i just hook up the vac nipple off of the fpr to any vac line
what wire gets tapped for the msd 6 white wire
thanks hopefully i can get it running soon
what dose each wire do on the 4 wire tps off an auto(92-93)
what dose each wire do on the Distributor (theres 3)
is it ok to hook up a msd and my megasquirt all to the ignition switch
and can i just hook up the vac nipple off of the fpr to any vac line
what wire gets tapped for the msd 6 white wire
thanks hopefully i can get it running soon
1993 MX-3 GS V6 - Stock
2004 MazdaSpeed MX-5
2004 RX-8 - Project
2004 MazdaSpeed MX-5
2004 RX-8 - Project
Re: Problems with fuel management install
i need to know what each wire dose on the tps for the auto
theres 4 wires
black with brown
red with white
green with red
green with white
i think the black with brown is the ground
the green with red is the 5v
then not sure about the other 2
heres a pic of the wiring diagram
<img src="http://10.pichold.com/tpswith_text.jpg" alt=" - " />
thanks
<small>[ August 03, 2004, 07:33 PM: Message edited by: Marlon ]</small>
theres 4 wires
black with brown
red with white
green with red
green with white
i think the black with brown is the ground
the green with red is the 5v
then not sure about the other 2
heres a pic of the wiring diagram
<img src="http://10.pichold.com/tpswith_text.jpg" alt=" - " />
thanks
<small>[ August 03, 2004, 07:33 PM: Message edited by: Marlon ]</small>
1993 MX-3 GS V6 - Stock
2004 MazdaSpeed MX-5
2004 RX-8 - Project
2004 MazdaSpeed MX-5
2004 RX-8 - Project
-
- Regular Member
- Posts: 1704
- Joined: December 31st, 2005, 5:54 pm
- Location: Burlington + Grimsby, Ontario, Canada
- Contact:
sorry to bring up such a old topic, did this ever get compleated. im at the point where i need to know how to get the electronic advance working with the Distributor.
Bochek
Bochek
Adam Bochek's 93 1.6L SOHC http://www.bochek.ca/car.gif
- ryanlindenberg
- Regular Member
- Posts: 874
- Joined: February 24th, 2003, 2:01 am
- Location: Minnesota
Ok here it goes:
Red/Green = +5 Volts
Green/White = Throttle %
Black/Brown = Ground
Red/White = Idle Switch
Red/Green = +5 Volts
Green/White = Throttle %
Black/Brown = Ground
Red/White = Idle Switch
CARDOMAIN WITH UPDATED PICS
"There are 2 kinds of pedestrians, the quick and the dead."
"There are 2 kinds of pedestrians, the quick and the dead."
-
- Regular Member
- Posts: 1704
- Joined: December 31st, 2005, 5:54 pm
- Location: Burlington + Grimsby, Ontario, Canada
- Contact:
where does it get the throttle % from? isnt the tps only a idle/cruse/wot switch?ryanlindenberg wrote:Ok here it goes:
Red/Green = +5 Volts
Green/White = Throttle %
Black/Brown = Ground
Red/White = Idle Switch
Bochek
Adam Bochek's 93 1.6L SOHC http://www.bochek.ca/car.gif
-
- Regular Member
- Posts: 1704
- Joined: December 31st, 2005, 5:54 pm
- Location: Burlington + Grimsby, Ontario, Canada
- Contact:
also, i have the b6 sohc, so its going to be different then the dohc engine wiring harness. my manual doesnt show thoes colour wires and its too dark out to go look @ my car, so for now il take your word on it, i just need to know where it gets the signals and how this could be configured with MSnS-E
Bochek
Bochek
Adam Bochek's 93 1.6L SOHC http://www.bochek.ca/car.gif
- ryanlindenberg
- Regular Member
- Posts: 874
- Joined: February 24th, 2003, 2:01 am
- Location: Minnesota
yea i don't know if your SOHC will be the same or not. colors should be similar i would think though.
anywho, it does send the throttle %, it shows up on my Haltech. I'm using a 95 TPS.
anywho, it does send the throttle %, it shows up on my Haltech. I'm using a 95 TPS.
CARDOMAIN WITH UPDATED PICS
"There are 2 kinds of pedestrians, the quick and the dead."
"There are 2 kinds of pedestrians, the quick and the dead."
-
- Regular Member
- Posts: 1704
- Joined: December 31st, 2005, 5:54 pm
- Location: Burlington + Grimsby, Ontario, Canada
- Contact:
ahh thats because of the 95 tps, so that means that the disty can not be getting that input from my setup, (no throttle % tps)
has anyone actually installed a msns on a b6?
Bochek
has anyone actually installed a msns on a b6?
Bochek
Adam Bochek's 93 1.6L SOHC http://www.bochek.ca/car.gif
- ryanlindenberg
- Regular Member
- Posts: 874
- Joined: February 24th, 2003, 2:01 am
- Location: Minnesota
there is a guy on this forum that says he has one installed... his name is Custommx3...may be the same guy as on here
probably not on a SOHC but at least he could help with some of the MS&S stuff.
http://www.mp3car.com/vbulletin/showthread.php?t=65821
![Question :?:](./images/smilies/icon_question.gif)
http://www.mp3car.com/vbulletin/showthread.php?t=65821
Last edited by ryanlindenberg on July 29th, 2006, 11:04 pm, edited 1 time in total.
CARDOMAIN WITH UPDATED PICS
"There are 2 kinds of pedestrians, the quick and the dead."
"There are 2 kinds of pedestrians, the quick and the dead."
-
- Regular Member
- Posts: 1704
- Joined: December 31st, 2005, 5:54 pm
- Location: Burlington + Grimsby, Ontario, Canada
- Contact:
your link goes to a ebay ad for a twin loop muffler
Adam Bochek's 93 1.6L SOHC http://www.bochek.ca/car.gif
- ryanlindenberg
- Regular Member
- Posts: 874
- Joined: February 24th, 2003, 2:01 am
- Location: Minnesota
sorry, fixed it!
CARDOMAIN WITH UPDATED PICS
"There are 2 kinds of pedestrians, the quick and the dead."
"There are 2 kinds of pedestrians, the quick and the dead."
- MechaManZero
- Regular Member
- Posts: 690
- Joined: March 20th, 2006, 7:36 pm
green and white is def going to the green and white wir on the VAF. Rock on ![Razz :P](./images/smilies/icon_razz.gif)
![Razz :P](./images/smilies/icon_razz.gif)
Çlark
![Image](http://i64.photobucket.com/albums/h192/Mechamanzero/MX-3/2mx3.jpg)
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
![Image](http://i64.photobucket.com/albums/h192/Mechamanzero/MX-3/2mx3.jpg)
95 Mazda MX3 4 Banger
Currently: H&R Lowering springs, BPT from a GTR, 18.5x6x3.5 same side inlet and outlet intercooler, Centerforce Dual Friction clutch
For BPT Frorums - http://www.aokforums.com/mazdaengines/
-
- Regular Member
- Posts: 1704
- Joined: December 31st, 2005, 5:54 pm
- Location: Burlington + Grimsby, Ontario, Canada
- Contact:
you guys are deffenlty talking doch wiring harness here.
Bochek
Bochek
Adam Bochek's 93 1.6L SOHC http://www.bochek.ca/car.gif