Page 1 of 3
Intake+TB question.
Posted: March 18th, 2011, 3:24 pm
by cWs306
eh whatsup. i got a issue, if i got a millenia intake and all that jazz, but no throttle body. would i be able to use the throttle body that came on the ZE originally on the millenia intake? or do i need to find the specific throttle body for that intake??
Re: Intake+TB question.
Posted: March 18th, 2011, 11:43 pm
by Nd4SpdSe
Need a curved neck TB for the curved neck IM. JDM or USDM it doesn't matter. both the KL47 and KL68 are identical. I had both.
Re: Intake+TB question.
Posted: March 19th, 2011, 3:31 am
by cWs306
ahhhh gotcha! thank you sir! now onto the TB hunt. last part needed
Re: Intake+TB question.
Posted: March 19th, 2011, 6:29 am
by WhiteFinish
Like said above..
The IAC black thing doesn'[t work and interfear with your intake.
Re: Intake+TB question.
Posted: March 23rd, 2011, 9:52 pm
by Mr.mx-3
I dunno if this pertains to anything here but I took the IAC off the ze TB I had and used it on my K8's when it went bad just to get me by untill I could do my swap and the car ran fine so most of the parts are idinical no matter what spec. J or A it should work. I'm with NE4SPDSE on this one you should get it from the same type intake you have.
Re: Intake+TB question.
Posted: March 23rd, 2011, 10:01 pm
by Nd4SpdSe
Mr.mx-3 wrote:I'm with ND4SPDSE on this one you should get it from the same type intake you have.
You don't usually have a choice, a straight neck one doesn't fit, a K8 one does but well, that's really restrictive for the 2.5
Re: Intake+TB question.
Posted: April 2nd, 2011, 7:00 pm
by cWs306
hey, question. so the KL02 throttle body wont work.? off a 626???
Re: Intake+TB question.
Posted: April 2nd, 2011, 8:04 pm
by Nd4SpdSe
Does the 626 have a curved neck IM?
Re: Intake+TB question.
Posted: April 2nd, 2011, 8:07 pm
by Ryan
Re: Intake+TB question.
Posted: April 2nd, 2011, 8:59 pm
by Daninski
How about this.
Make it so number one.
Re: Intake+TB question.
Posted: April 2nd, 2011, 10:17 pm
by RS_OBD'oh_2
Hahahaha.
Re: Intake+TB question.
Posted: April 3rd, 2011, 12:28 pm
by cWs306
sorry guys, im new to this swap. idunno exactly what makes these not work, wheres the IAC? is that the plug on the side of the TB? or is it on the bottom of it? if so the KL02 i found wouldnt work? cause it would hit the fuel/cooling lines? im so confused. heres a picture on the IM/TB...
Re: Intake+TB question.
Posted: April 3rd, 2011, 12:30 pm
by cWs306
You don't usually have a choice, a straight neck one doesn't fit, a K8 one does but well, that's really restrictive for the 2.5
sooooo? should i just get my k8 TB bored to 65mm?
Re: Intake+TB question.
Posted: April 3rd, 2011, 4:11 pm
by Nd4SpdSe
The IAC is the lower part of the TB, it's got the electrical connection to it
No, the K8 TB will not bore out to KL spec
This is a curved beck IM, you need the TB off of one of those, DE or ZE, they'r the same.
Re: Intake+TB question.
Posted: April 3rd, 2011, 4:49 pm
by cWs306
yah i got a curved neck already.. i just need a TB. and i was told the K8 one will bore out to KL spec?? :S