MX3-4U2NV - 1996 MX-3 GS - Polished Headlights
- MX3-4U2NV
- Regular Member
- Posts: 546
- Joined: August 25th, 2009, 9:51 pm
- antispam: No
- Location: Mississauga, Ontario
MX3-4U2NV - 1996 MX-3 GS - Polished Headlights
TABLE OF CONTENTS
1. Introduction post (This post)
2. To-do list - May 13, 2010
3. Tinted tails, chrome door handles, repainted interior - May 16, 2010
4. Stereo Install - May 23, 2010
5. Rims installed - June 8, 2010
6. Polished Headlights - July 29, 2010
So, I guess I better start one of these.
First off, it's currently your typical Black 1996 GS. Nothing special, we've all seen them, know what they look like, etc. No need to post pictures of that.
Things done so far
- new NGK wires
- new NGK plugs
- KYB GR2 struts all the way around
- B&M Short Shifter
- wheels
- repaint interior
- stereo install
- homemade intake
- Rims installed
Plans so far
- body work
- possible DECENT body mouldings/skirts
- typical KL-ZE swap
- turbo the KL-ZE (again, typical)
- decent interior customization like new carpets, door panels, etc
- Stainless Steel brake lines
the list goes on...
Anything more specific, I will post here.
My brother had a 1995 GS he swapped a KL-ZE in to when he blew his 1.8L. I'd like to get my car to the caliber I thought my younger brothers was. Nostalgia I guess.
Here is a pic of my brother's car
One day I hope to have my brother help me with my car as I did his.
1. Introduction post (This post)
2. To-do list - May 13, 2010
3. Tinted tails, chrome door handles, repainted interior - May 16, 2010
4. Stereo Install - May 23, 2010
5. Rims installed - June 8, 2010
6. Polished Headlights - July 29, 2010
So, I guess I better start one of these.
First off, it's currently your typical Black 1996 GS. Nothing special, we've all seen them, know what they look like, etc. No need to post pictures of that.
Things done so far
- new NGK wires
- new NGK plugs
- KYB GR2 struts all the way around
- B&M Short Shifter
- wheels
- repaint interior
- stereo install
- homemade intake
- Rims installed
Plans so far
- body work
- possible DECENT body mouldings/skirts
- typical KL-ZE swap
- turbo the KL-ZE (again, typical)
- decent interior customization like new carpets, door panels, etc
- Stainless Steel brake lines
the list goes on...
Anything more specific, I will post here.
My brother had a 1995 GS he swapped a KL-ZE in to when he blew his 1.8L. I'd like to get my car to the caliber I thought my younger brothers was. Nostalgia I guess.
Here is a pic of my brother's car
One day I hope to have my brother help me with my car as I did his.
Last edited by MX3-4U2NV on July 29th, 2010, 8:19 pm, edited 10 times in total.
- MX3-4U2NV
- Regular Member
- Posts: 546
- Joined: August 25th, 2009, 9:51 pm
- antispam: No
- Location: Mississauga, Ontario
Re: MX3-4U2NV - 1996 MX-3 GS
TO BE INSTALLED
Just recently acquired the Eibachs I was looking for
To be installed next spring for the season. They came with Tokico Rs's struts.
Just recently acquired the Eibachs I was looking for
To be installed next spring for the season. They came with Tokico Rs's struts.
- MX3-4U2NV
- Regular Member
- Posts: 546
- Joined: August 25th, 2009, 9:51 pm
- antispam: No
- Location: Mississauga, Ontario
Re: MX3-4U2NV - 1996 MX-3 GS
Nothing to update aside from having acquired a few parts here and there.
Car hasn't ran since the first week of December.
Car hasn't ran since the first week of December.
- MX3-4U2NV
- Regular Member
- Posts: 546
- Joined: August 25th, 2009, 9:51 pm
- antispam: No
- Location: Mississauga, Ontario
Re: MX3-4U2NV - 1996 MX-3 GS
Well, the car apparently lives.
As I wrote before, the car hasn't ran since the beginning of December, 2009.
It was at a shop, apparently got fixed, and was given back. On the way home it brok down again.
That was 6 weeks ago.
Well, I got the used disty off of Night Shade, and whamo, she starts. Just taping up a few wires, going for a test run, and I should take it home tonight.
As I wrote before, the car hasn't ran since the beginning of December, 2009.
It was at a shop, apparently got fixed, and was given back. On the way home it brok down again.
That was 6 weeks ago.
Well, I got the used disty off of Night Shade, and whamo, she starts. Just taping up a few wires, going for a test run, and I should take it home tonight.
- _-Night-Shade-_
- Senior Member
- Posts: 2664
- Joined: January 15th, 2009, 8:00 pm
- Location: Toronto, Ontario, Canada
Re: MX3-4U2NV - 1996 MX-3 GS
Glad to revive a fellow MX-3
- MX3-4U2NV
- Regular Member
- Posts: 546
- Joined: August 25th, 2009, 9:51 pm
- antispam: No
- Location: Mississauga, Ontario
Re: MX3-4U2NV - 1996 MX-3 GS
A friend of mine and I were planning on having a "Minor Mechanics" day, where we will work on all the little quirks, etc., we think need to be done to our cars.
Here is my 'To-Do' list:
- bezel lights
- hvac lights
- rear strut bar
- speakers
- speaker wires
- shifter boot
- clean rims
- repaint previous owners mess (they painted a few interior pieces silver, which is chipping and scratched to crap)
- remove old tint (it's very bad, peeling, etc)
- patch small hole under drivers door
- peel unwanted decals from previous owner
- vacuum
- shampoo
That's my list I hope to accomplish on the 22nd. First thing in the morning though, we're hitting a couple junk yards, then heading home for a day of repairs, beers, and bbq.
Here is my 'To-Do' list:
- bezel lights
- hvac lights
- rear strut bar
- speakers
- speaker wires
- shifter boot
- clean rims
- repaint previous owners mess (they painted a few interior pieces silver, which is chipping and scratched to crap)
- remove old tint (it's very bad, peeling, etc)
- patch small hole under drivers door
- peel unwanted decals from previous owner
- vacuum
- shampoo
That's my list I hope to accomplish on the 22nd. First thing in the morning though, we're hitting a couple junk yards, then heading home for a day of repairs, beers, and bbq.
Last edited by MX3-4U2NV on June 8th, 2010, 11:53 pm, edited 1 time in total.
Re: MX3-4U2NV - 1996 MX-3 GS
I have these for sale [FS]. Only a few thousand K on the wheels and tires. http://www.mx-3.com/phpBB3/viewtopic.php?f=2&t=72015" onclick="window.open(this.href);return false;
2004 Subaru WRX Silver, stage 2, minty interior.
2002 Subaru WRX Blue, SOLD (best E test numbers I've ever seen)
94 MX-6. Sold
92 GS KLZE 5 Speed
96 GS 5 speed, KLZE, Sold
95 GS Minty Shape Sold
92 GS Sold
92 GS Parts Car scrapped.
Feedback viewtopic.php?f=37&t=66348" onclick="window.open(this.href);return false;
7477th member.
I know you believe that you understand what you think I said but I'm sure you realize that what you heard is not what I meant.
2002 Subaru WRX Blue, SOLD (best E test numbers I've ever seen)
94 MX-6. Sold
92 GS KLZE 5 Speed
96 GS 5 speed, KLZE, Sold
95 GS Minty Shape Sold
92 GS Sold
92 GS Parts Car scrapped.
Feedback viewtopic.php?f=37&t=66348" onclick="window.open(this.href);return false;
7477th member.
I know you believe that you understand what you think I said but I'm sure you realize that what you heard is not what I meant.
- MX3-4U2NV
- Regular Member
- Posts: 546
- Joined: August 25th, 2009, 9:51 pm
- antispam: No
- Location: Mississauga, Ontario
Re: MX3-4U2NV - 1996 MX-3 GS
PM'dDaninski wrote:I have these for sale [FS]. Only a few thousand K on the wheels and tires. http://www.mx-3.com/phpBB3/viewtopic.php?f=2&t=72015" onclick="window.open(this.href);return false;
- MX3-4U2NV
- Regular Member
- Posts: 546
- Joined: August 25th, 2009, 9:51 pm
- antispam: No
- Location: Mississauga, Ontario
Minor work done - May 16, 2010
Did some minor things to the car a couple weekends back... Took pics, just neglected to post. So here is a small update.
Sunday May 16rh, 2010 - Tinted and installed Altezza's, installed chrome door handles, complete repainted interior.
(click on thumbs to enlarge)
Sunday May 16rh, 2010 - Tinted and installed Altezza's, installed chrome door handles, complete repainted interior.
(click on thumbs to enlarge)
Last edited by MX3-4U2NV on June 8th, 2010, 11:38 pm, edited 1 time in total.
- MX3-4U2NV
- Regular Member
- Posts: 546
- Joined: August 25th, 2009, 9:51 pm
- antispam: No
- Location: Mississauga, Ontario
Stereo Install - May 23, 2010
reserved for pics and info
- MX3-4U2NV
- Regular Member
- Posts: 546
- Joined: August 25th, 2009, 9:51 pm
- antispam: No
- Location: Mississauga, Ontario
Wheel Install - June 8, 2010
Installed my ADR SOKUDO 8's this evening after work. Got some black lugs for the install too.
DEFINITELY need to paint and clean the wheel wells. Also, still need to install the Eibach's.
DEFINITELY need to paint and clean the wheel wells. Also, still need to install the Eibach's.
Last edited by MX3-4U2NV on July 4th, 2010, 2:03 pm, edited 1 time in total.
-
- Regular Member
- Posts: 1751
- Joined: November 2nd, 2009, 3:03 am
- antispam: No
- Location: Vancouver, BC
Re: MX3-4U2NV - 1996 MX-3 GS
looking good. is that gunmetal paint for the interior?
- MX3-4U2NV
- Regular Member
- Posts: 546
- Joined: August 25th, 2009, 9:51 pm
- antispam: No
- Location: Mississauga, Ontario
Re: MX3-4U2NV - 1996 MX-3 GS
Slightly darker. It's a colour I eventually want to paint the exterior.mikeinaus wrote:looking good. is that gunmetal paint for the interior?
-
- Regular Member
- Posts: 1751
- Joined: November 2nd, 2009, 3:03 am
- antispam: No
- Location: Vancouver, BC
Re: MX3-4U2NV - 1996 MX-3 GS
go for it. ive wanted to get mine painted that colour too but i cant afford to paint mine.