I need a performance transmission.
-
- Junior Member
- Posts: 3
- Joined: November 29th, 2007, 9:26 pm
I need a performance transmission.
Hey everyone hows it going? Ok I found everything i need to make my KLZE a beast, The only problem im having is the transmission and Crankshaft. I need both of these to be high performance. If anyone has any ideas please let me know. thanks.
- solo_ryder
- Senior Member
- Posts: 6289
- Joined: October 16th, 2004, 2:01 am
- Location: British Columbia
- tehbrookzorz
- Regular Member
- Posts: 1561
- Joined: April 29th, 2006, 6:59 pm
- Location: Calgary, Alberta
-
- Junior Member
- Posts: 3
- Joined: November 29th, 2007, 9:26 pm
Basically got a high performance engine kit from http://www.importperformanceparts.com. The kit holds up to 60lbs of boost. I will never run it this high but i need a transmission thats gonna hold up to about 7-800 horsepower.
-
- Forum Moderator
- Posts: 3415
- Joined: September 3rd, 2002, 2:01 am
- Location: Eastern Hemisphere
- Contact:
LOL funny stuff....92MX3TURBO wrote: up to about 7-800 horsepower.
Try posting in the tranmission forum next time when you have transmission questions
08 Infiniti G37s 6speed (The Daily)
Stillen Cold Air Intake, Z1 Plenum Power Mod, Z1 Headers, Z1 Test Pipe, OBX (Ark) Exhaust, Up-Rev Osiris Engine Management (Tuned at Z1), 20x9" 20x10" Str Racing Concave Staggered Rims, SPC Camber kit, Tein H Techs Springs
01 Lexus Is300 (LS2 Project)
93 Mx3 SE 2.5 KLZE (sold it)
93 Mx3 GS 2.0 KFZE (killed it)
Stillen Cold Air Intake, Z1 Plenum Power Mod, Z1 Headers, Z1 Test Pipe, OBX (Ark) Exhaust, Up-Rev Osiris Engine Management (Tuned at Z1), 20x9" 20x10" Str Racing Concave Staggered Rims, SPC Camber kit, Tein H Techs Springs
01 Lexus Is300 (LS2 Project)
93 Mx3 SE 2.5 KLZE (sold it)
93 Mx3 GS 2.0 KFZE (killed it)
- mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
that ze will be making 700-800hp..umm ok. Maybe you should be buying a mustang not a ze mx-3
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks
http://www.cardomain.com/id/mitmaks
-
- Regular Member
- Posts: 50
- Joined: November 14th, 2007, 1:09 pm
you have a V6 ZE pushing 800 horses? congratulations you have managed to break the laws of physics, only way i would believe that is with a dyno and some alcohol (in me not the car) lol but in all fairness i do not meen to be an ---, all i am saying is you must be confused or wrong, or i must be seriusly underestimating KLZE engines
- PATDIESEL
- Senior Member
- Posts: 4476
- Joined: August 13th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Atlanta, GA.
Topic moved. Please take a minute to look at the different forums before you post so that you are sure you are starting a post in the correct section.
The K series motors have a pretty darn stout crank from the factory. IIRC they are forged. I also doubt that you will put that many horses in a ZE. As for the trans, if you want a performance one look at Quaife- they, and others sell sequential transmissions that you can buy to handle closer to your 7-800 HP goal, but even they willl not hold that much. They are for FWD and you would need an adapter plate and new shift linkage, but would be doable with enough money. IIRC the trannies are in the 4-10,000 range.
The K series motors have a pretty darn stout crank from the factory. IIRC they are forged. I also doubt that you will put that many horses in a ZE. As for the trans, if you want a performance one look at Quaife- they, and others sell sequential transmissions that you can buy to handle closer to your 7-800 HP goal, but even they willl not hold that much. They are for FWD and you would need an adapter plate and new shift linkage, but would be doable with enough money. IIRC the trannies are in the 4-10,000 range.
ZE -strait neck,headers,2.5 exhaust,pheno spacers,lower cross member,GC coils,MS struts,Brembo slotted rotors,filled MS mounts,SS brake/clutch lines, CAI,to rear bat reloc,Hella headlamps,Hella DE fogs 180WHP
- mx3autozam
- Senior Member
- Posts: 2950
- Joined: September 24th, 2005, 9:09 pm
- Location: Kitchener
Re: I need a performance transmission.
Any KL holding 60pounds of boost..haha ya right!
93 Mazda MX3 KLZE Turbo
Re: I need a performance transmission.
He never said how big (or small) the turbo would bemx3autozam wrote:Any KL holding 60pounds of boost..haha ya right!
MrMazda92 wrote:I find Honduh forums more helpful, typically more pleasant too.
- solo_ryder
- Senior Member
- Posts: 6289
- Joined: October 16th, 2004, 2:01 am
- Location: British Columbia
Re: I need a performance transmission.
Not this guy again, I seen this dude post under 4 different user ID's with his stupid 60psi turbo kit
- mx3autozam
- Senior Member
- Posts: 2950
- Joined: September 24th, 2005, 9:09 pm
- Location: Kitchener
Re: I need a performance transmission.
WOW!
92 Blaze Red MAZDA Mx3 <GS> ZE, millenia manifold. gutted interior, filled mounts, fidanza fw, act 6puck.
- Mooneggs
- Forum Moderator
- Posts: 6128
- Joined: August 10th, 2005, 10:08 pm
- antispam: ~SPAM*SUX~
- Location: Hillsboro, OR
- Contact:
Re: I need a performance transmission.
LOL I love it when the calm ones get pissed off...solo_ryder wrote:Not this guy again, I seen this dude post under 4 different user ID's with his stupid 60psi turbo kit
My Feedback
92 mx-3 gs klze 'race car' IP 15.05 @ 92.5mph
92 mx-3 gs klze 'daily driver' IP 14.55 @ 95.7mph
http://www.cardomain.com/id/Mooneggs
92 mx-3 gs klze 'race car' IP 15.05 @ 92.5mph
92 mx-3 gs klze 'daily driver' IP 14.55 @ 95.7mph
http://www.cardomain.com/id/Mooneggs
- Aston Wards
- Regular Member
- Posts: 761
- Joined: December 28th, 2001, 2:01 am
- Location: Christchurch, New Zealand
Re: I need a performance transmission.
60psi??? i'd hope to get more than 800hp with that much boost!
91 Eunos Presso KF-ZE
89 Nissan 300ZX TT 2+2
90 Nissan 300ZX TT 2+0
89 Nissan 300ZX TT 2+2
90 Nissan 300ZX TT 2+0