GOT TRACTION!?

A forum for posting automotive related Images & Video Clips. (Please keep it clean, no profanity or offensive material.)
Post Reply
!vtec-this!
Regular Member
Posts: 110
Joined: March 9th, 2006, 6:07 pm
Location: Bristol R.I.

GOT TRACTION!?

Post by !vtec-this! »

check out my new wheels can u say taction? what do u think?

Image

http://www.gotklze.com/forum/vbgarage.p ... mage&id=38
Last edited by !vtec-this! on December 29th, 2006, 4:35 pm, edited 4 times in total.
http://profile.myspace.com/index.cfm?fu ... d=77496445
My Car: Mazda MX-3 v6
14.5 @97mph
2.328 60ft....still more room for improvement
Only 165whp
Now boosted & New #'s to come
User avatar
Custommx3
Site Administrator
Posts: 8391
Joined: November 7th, 2000, 2:01 am
antispam: ~SPAM*SUX~
Location: Lat 35.1N Lon -90W
Contact:

Post by Custommx3 »

VERY nice!
User avatar
XxantwawnxX
Regular Member
Posts: 1281
Joined: January 8th, 2005, 11:08 pm
Location: Newportnews VA

Post by XxantwawnxX »

i can also say broken axles!! : P haha nice man
Image

* * * * * * 92 Mx3 ZET, rear/front swaybars,srd crossmember,HKS SSQV,cold air,ZE with millinia mani and TB and 280cc injectors,INtrax springs with tokiko HP struts, Grounding kit, MotegiTrakLite wheels 17's at 14lbs each, MSnS Running fuel and spark,HEI mod,T3/To4E .60/.63 stage 3 turbine,3rd gen rx7 fuel pump, SSAC Headers/hotpipes ,38 ext tial wastegate, findanza flywheel, SBC TZ clutch/pressureplate,braille11pound battery/ magnum drilled F/R rotors,projectors, CXmotorsports almuminum intercooler.
Mnemonic
Forum Moderator
Posts: 3415
Joined: September 3rd, 2002, 2:01 am
Location: Eastern Hemisphere
Contact:

Post by Mnemonic »

snap pop clank axle be gone!!!!
08 Infiniti G37s 6speed (The Daily)
Stillen Cold Air Intake, Z1 Plenum Power Mod, Z1 Headers, Z1 Test Pipe, OBX (Ark) Exhaust, Up-Rev Osiris Engine Management (Tuned at Z1), 20x9" 20x10" Str Racing Concave Staggered Rims, SPC Camber kit, Tein H Techs Springs

01 Lexus Is300 (LS2 Project)
93 Mx3 SE 2.5 KLZE (sold it)
93 Mx3 GS 2.0 KFZE (killed it)
!vtec-this!
Regular Member
Posts: 110
Joined: March 9th, 2006, 6:07 pm
Location: Bristol R.I.

Post by !vtec-this! »

i should be fine as long as i ain't popin the clutch..... i hope :)
http://profile.myspace.com/index.cfm?fu ... d=77496445
My Car: Mazda MX-3 v6
14.5 @97mph
2.328 60ft....still more room for improvement
Only 165whp
Now boosted & New #'s to come
Juans_93_MX3
Senior Member
Posts: 2220
Joined: October 17th, 2004, 2:01 am
Location: SLC, Utah

Post by Juans_93_MX3 »

No videos? Just a pic?
2008 Mazda 3
1993 MX3 GS
KLZE, Fidanza flywheel, KL31 CAMs, South Bend Stage I Clutch, Pacesetter STS, SS AutoChromes, Magnaflow muffler, 2.25' Exhaust, CAI, Blaster Coil HEI, KLDE Valvetrain, 5 Speed Swap
!vtec-this!
Regular Member
Posts: 110
Joined: March 9th, 2006, 6:07 pm
Location: Bristol R.I.

Post by !vtec-this! »

no vids as of now because i just got them and iam in the processes of rebuilding my heads
http://profile.myspace.com/index.cfm?fu ... d=77496445
My Car: Mazda MX-3 v6
14.5 @97mph
2.328 60ft....still more room for improvement
Only 165whp
Now boosted & New #'s to come
User avatar
Limegreen mx-3
Regular Member
Posts: 1778
Joined: October 29th, 2002, 2:01 am
Location: San Antonio TX
Contact:

Post by Limegreen mx-3 »

nice rim and slicks better than mine i have the 15gs honey cone rims on MT slicks. better than street tires on the track. if ur easy off the line be good i still have a weal f-series trans with stocl axles mated to a boosted BP. iam still surpise i have broken a diff or snap a axles.
(12.4@118@18psi) 92 MX-3, KIA (BP-DE)Swap, Electromotive TEC II Standalone, 8,200 Rev Limit, Custom Intake/Exhaust Manifold, 1,000cc PTE Injectors, Custom Fuel Rail, Aeromotive FPR, 80MM Holley TB, MSD 8.5MM Wires, NGK V-Power #8, SC6262 Turbo, 3 in. DownPipe, Tial WG/BOV, 600HP PTE FMIC, 2.5IN Intercooler Piping, EQUUS/Autometer KIA G-Series Tran, Extreme ACT Clutch, Built BP in starting process.
Post Reply

Return to “Images/Videos Forum”