This would be death...projectzemx3 wrote:the best things we could make CF
94+ dash (not the dash board) that comes down to around the shifter (that would be sex)
Have you ever seen how reflective cf is in the sunlight?
CARBON FIBRE PRODUCTS
-
Mnemonic
- Forum Moderator
- Posts: 3415
- Joined: September 3rd, 2002, 2:01 am
- Location: Eastern Hemisphere
- Contact:
Re: CARBON FIBRE PRODUCTS
Have you ever seen how reflective cf is in the sunlight?
08 Infiniti G37s 6speed (The Daily)
Stillen Cold Air Intake, Z1 Plenum Power Mod, Z1 Headers, Z1 Test Pipe, OBX (Ark) Exhaust, Up-Rev Osiris Engine Management (Tuned at Z1), 20x9" 20x10" Str Racing Concave Staggered Rims, SPC Camber kit, Tein H Techs Springs
01 Lexus Is300 (LS2 Project)
93 Mx3 SE 2.5 KLZE (sold it)
93 Mx3 GS 2.0 KFZE (killed it)
Stillen Cold Air Intake, Z1 Plenum Power Mod, Z1 Headers, Z1 Test Pipe, OBX (Ark) Exhaust, Up-Rev Osiris Engine Management (Tuned at Z1), 20x9" 20x10" Str Racing Concave Staggered Rims, SPC Camber kit, Tein H Techs Springs
01 Lexus Is300 (LS2 Project)
93 Mx3 SE 2.5 KLZE (sold it)
93 Mx3 GS 2.0 KFZE (killed it)
-
mx-3_4evr
- Regular Member
- Posts: 609
- Joined: February 8th, 2008, 12:15 am
- Location: Burnsville,MN
- Contact:
Re: CARBON FIBRE PRODUCTS
Not dry carbon fiber 
Re: CARBON FIBRE PRODUCTS
How about a modified rsx rear lip in CF? Any news on the r&d front for more cf stuff???
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
Re: CARBON FIBRE PRODUCTS
i'd rather have a brunetteprojectzemx3 wrote:the best things we could make CF
a cf blonde for the passenger seat that cant talk.
94 mx3 rs
92 mx3 gs curved neck klze SOLD
92 mx3 gs curved neck klze SOLD
Re: CARBON FIBRE PRODUCTS
+1 for the rsx rear lip, and an oem front lip, and oem sides. Please!?93vtecklr wrote:How about a modified rsx rear lip in CF? Any news on the r&d front for more cf stuff???
Re: CARBON FIBRE PRODUCTS
I would want a hatch garnish without the spoiler on it
+1 for the angry eyes cf hood!
+1 fenders
+1 MS bumper
+1 rad support
+1 exterior door handles
+1 94+ dash!
+1 for the angry eyes cf hood!
+1 fenders
+1 MS bumper
+1 rad support
+1 exterior door handles
+1 94+ dash!
Re: CARBON FIBRE PRODUCTS
Contact Oscar for the rad support, 125 plus shipping and donation i believe
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
-
Nd4SpdSe
- Senior Member
- Posts: 11212
- Joined: May 25th, 2002, 2:01 am
- Location: Québec City, Quebec, Canada
- Contact:
Re: CARBON FIBRE PRODUCTS
Honestly, I'd like an RSX rear lip in CF too
1992 Mazda Mx-3 GSR - 2.5L KLZE : Award Winning Show Car & Race Car ['02-'09] (Retired)
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
Re: CARBON FIBRE PRODUCTS
alright, we're +3 for the modified rsx rear lip in CF!!!
1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler.
1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes
1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
Re: CARBON FIBRE PRODUCTS
This may seem kinda ridiculous but has anyone considered CF rocker panels, fenders, engine crossmember, underbody panelling, or any other rust-attracting parts?
I'm not sure how you could smoothly join steel with CF to integrate rocker panels, but that would be truly awesome.
Or what about chassis stiffening bars? Ultralight, strong CF bars you could bolt from subframe to subframe. Rust-free, lightweight...
I'm not sure how you could smoothly join steel with CF to integrate rocker panels, but that would be truly awesome.
Or what about chassis stiffening bars? Ultralight, strong CF bars you could bolt from subframe to subframe. Rust-free, lightweight...
- Gord
1996 MX-3 GS-ZE 2.5L 5spd
KLZE+LSD / Headers / KL02 VAF / Clutchmasters stage-I / Fidanza 9lb flywheel / Eibach Pro Kit / Tokico HPs / Urethane bushings & mounts / SSR Comp-C 16x7 / General Exclaim UHP 205/45R16 / Wilwood 13" brakes / Whiteline rear swaybar / Carputer / Software Crossover / Infinity components+subs / 41hz Tripath Amp9 / Trunk SLA batt / Keyless entry
1996 MX-3 GS-ZE 2.5L 5spd
KLZE+LSD / Headers / KL02 VAF / Clutchmasters stage-I / Fidanza 9lb flywheel / Eibach Pro Kit / Tokico HPs / Urethane bushings & mounts / SSR Comp-C 16x7 / General Exclaim UHP 205/45R16 / Wilwood 13" brakes / Whiteline rear swaybar / Carputer / Software Crossover / Infinity components+subs / 41hz Tripath Amp9 / Trunk SLA batt / Keyless entry
-
fowljesse
- Supporting Member
- Posts: 5676
- Joined: March 17th, 2006, 2:59 pm
- Location: portland, OR
- Contact:
Re: CARBON FIBRE PRODUCTS
Not to be a nay-sayer, but my underbody stuff all have dents and scuffs in them. If it were CF, it would have shattered. The crossmember and some other things could be protected by sheet metal. I was thinking how awesome it would be to lighten up the fron subframe when I was curling it the other day. It could lose 35lbs. and still be functional.
'93 GS - P&P DE w/ ZE exh. cams/ pistns, KLG4 IM, 65mm TB, MSnS, Phenos, K&N RAI, UDP, Grnd wires, rear batt, filld MM, torq strt, TWM short shftr, Exedy, Lng tube hdrs 2.5" Side exhaust, H&R sprngs, Poly bushngs, strutbars, Alum. crss mmber&tiebar, 22mm swybar, solid links, Direzzas, leather int, Alpine 9805 stereo & alrm, keyless entry, 10 Boston Accoustics spkrs, Prjectrs, Blaster2, CF hood, FG hatch, Lexan
Re: CARBON FIBRE PRODUCTS
Hmm.. is CF really that shatterable? What about if it was coated with a hard non-metallic resin?fowljesse wrote:Not to be a nay-sayer, but my underbody stuff all have dents and scuffs in them. If it were CF, it would have shattered. The crossmember and some other things could be protected by sheet metal. I was thinking how awesome it would be to lighten up the fron subframe when I was curling it the other day. It could lose 35lbs. and still be functional.
- Gord
1996 MX-3 GS-ZE 2.5L 5spd
KLZE+LSD / Headers / KL02 VAF / Clutchmasters stage-I / Fidanza 9lb flywheel / Eibach Pro Kit / Tokico HPs / Urethane bushings & mounts / SSR Comp-C 16x7 / General Exclaim UHP 205/45R16 / Wilwood 13" brakes / Whiteline rear swaybar / Carputer / Software Crossover / Infinity components+subs / 41hz Tripath Amp9 / Trunk SLA batt / Keyless entry
1996 MX-3 GS-ZE 2.5L 5spd
KLZE+LSD / Headers / KL02 VAF / Clutchmasters stage-I / Fidanza 9lb flywheel / Eibach Pro Kit / Tokico HPs / Urethane bushings & mounts / SSR Comp-C 16x7 / General Exclaim UHP 205/45R16 / Wilwood 13" brakes / Whiteline rear swaybar / Carputer / Software Crossover / Infinity components+subs / 41hz Tripath Amp9 / Trunk SLA batt / Keyless entry
Re: CARBON FIBRE PRODUCTS
Any news on fibre products coming out?
Re: CARBON FIBRE PRODUCTS
+1 for angry eyes hood
92 Mazda MX3 GS
http://www.cardomain.com/id/ukrman" onclick="window.open(this.href);return false; - cardomain page
viewtopic.php?f=46&t=66481 - worklog
viewtopic.php?f=37&t=72099 - feedback
viewtopic.php?f=2&t=71757 - stuff for sale
http://s2.metaldamage.com/c.php?uid=159229" onclick="window.open(this.href);return false; - biggest waste of time
http://www.cardomain.com/id/ukrman" onclick="window.open(this.href);return false; - cardomain page
viewtopic.php?f=46&t=66481 - worklog
viewtopic.php?f=37&t=72099 - feedback
viewtopic.php?f=2&t=71757 - stuff for sale
http://s2.metaldamage.com/c.php?uid=159229" onclick="window.open(this.href);return false; - biggest waste of time
-
Dragyn Vyrus
- Regular Member
- Posts: 228
- Joined: May 12th, 2008, 9:36 pm
- Location: Sherwood Park, Alberta
Re: CARBON FIBRE PRODUCTS
another +1 for angry eyes hood
93 MX-3 ZE-GS - Sold
95 MX-3 RS - Bone stock winter car.
92 JDM turbo MR2 - SSQV, Cusco strut tower bar, ATS intercooler kit, Berk Exhuast, HKS EVC-S
95 MX-3 RS - Bone stock winter car.
92 JDM turbo MR2 - SSQV, Cusco strut tower bar, ATS intercooler kit, Berk Exhuast, HKS EVC-S