Page 4 of 4
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: February 27th, 2013, 11:05 am
by kulluminati777
that rear wing is sweeet. I was wondering who picked that up from the auctions
![Freak :freak:](./images/smilies/freak.gif)
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: February 27th, 2013, 3:42 pm
by memphis9787
Thanks man, haha I didnt want to waste an oppotunity to snap it up, should arrive next week or so. Have you secured yourself some MS Seats yet? There is a few floating around at the moment.. BTW I used the BA Brackets, I think Rupe has them for about $80 or so
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: February 27th, 2013, 4:41 pm
by wytbishop
If I lived in the same country as Ruprecht I'd be is so much trouble all the time.
Nice ride my friend.
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: February 27th, 2013, 6:53 pm
by kulluminati777
memphis9787 wrote:Thanks man, haha I didnt want to waste an oppotunity to snap it up, should arrive next week or so. Have you secured yourself some MS Seats yet? There is a few floating around at the moment.. BTW I used the BA Brackets, I think Rupe has them for about $80 or so
with my head gasket issue and me not working anymore and going to school full time i had to dip into my MS seat fund. It´ll be 1600USD to get a set to my door. Which is not bad but im a little short. I also just bought a new BBK for the front
![Mr. Green :mrgreen:](./images/smilies/icon_mrgreen.gif)
hopefully the car is still running by the time it gets here
Rupe told me the BA brackets make the seat sit a little higher in the EC. Is it bad? or even noticeable?
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: February 28th, 2013, 5:18 am
by memphis9787
wytbishop wrote:If I lived in the same country as Ruprecht I'd be is so much trouble all the time.
Nice ride my friend.
Thanks mate, he gets great stuff, I just wish I had deeper pockets
kulluminati777 wrote:with my head gasket issue and me not working anymore and going to school full time i had to dip into my MS seat fund. It´ll be 1600USD to get a set to my door. Which is not bad but im a little short. I also just bought a new BBK for the front
![Mr. Green :mrgreen:](./images/smilies/icon_mrgreen.gif)
hopefully the car is still running by the time it gets here
Rupe told me the BA brackets make the seat sit a little higher in the EC. Is it bad? or even noticeable?
Sorry I worded that wrong, Ive got the BG/Mx3 Brackets but im 99% cerrtain the BA ones exactly the same, I have noticed they raise the seat a bit more than stock, but its not that bad unless you had a massive steering wheel or super fat legs
![Laughing :lol:](./images/smilies/icon_lol.gif)
. Also the seats are a def a snug fit, Im 6''2 but I think if I were any taller/wider sitting in these could be an issue
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: April 15th, 2013, 10:03 am
by memphis9787
Not much of an update but managed to locate a few rare goodies as of late,
Eunos Rear Light Up Badge
Eunos S/S Door sills,
And...
these bad boys
Thats about done it for all the OEM body parts I'll need for this build
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: April 16th, 2013, 8:23 pm
by bogaut
ooh pics of the eunos rear light up badge plz
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: May 1st, 2013, 12:34 pm
by memphis9787
bogaut wrote:ooh pics of the eunos rear light up badge plz
Will put a pic of it when it arrives, not sure whether I'll keep it or not, it was a bit of a hasty purchase as they are hard to come by, although I dont think it will suit the look im after...
I was mucking around with mounting places for my Boost and Wideband, I didnt want them in a pod cup on the dash or piller so with a bit of Acrylic, a lighter and slicing my hand with the stanly knife, voila
Prob not as centre as it should be but I'll fix it up a bit more
Single
Double, test fit, I'll prob end up siliconing in the frames in as opposed to using screws
![Image](http://i508.photobucket.com/albums/s326/memphis9787/2013-05-01-1345_zps5581979e.jpg)
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: May 24th, 2013, 4:53 am
by memphis9787
Still a bit indecisive on this wing
![Shrug :shrug:](./images/smilies/shrug.gif)
, I'll have to see how it suits once the car is back together
![Image](http://i508.photobucket.com/albums/s326/memphis9787/2013-05-23-1428_zps0f224e63.jpg)
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: May 24th, 2013, 8:52 am
by kulluminati777
oh man i didnt know it comes up like that. I thought it went straight out....Im in decisive whether i like it or not now too
![Laughing :lol:](./images/smilies/icon_lol.gif)
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: May 24th, 2013, 10:25 am
by memphis9787
Yeah man, I was hoping it just went straight out and elongated the stock wing, but it sort of curls up-ish, anyways I'll get painted, it might look better when the car is lowered with the jdm sides, I'll find out if it looks decent soon enough
![Laughing :lol:](./images/smilies/icon_lol.gif)
Re: Memphis9787's 94 Eunos Presso J-Spec BPT Swap
Posted: January 30th, 2014, 11:16 pm
by kulluminati777
Any updates on this sweet worklog?
![Very Happy :D](./images/smilies/icon_biggrin.gif)