Let's see your engine bays!!

MrMazda92 · Post by **MrMazda92** » September 27th, 2012, 1:56 am

Lol gas cap, that's exhaustion for you!

That's up there with A pillar bars and a few of Dan's posts!

I'll contribute one... This is my '93, before the nightmare with exhaust and coolant leaks began.

MazdaMan1991 · Post by **MazdaMan1991** » February 14th, 2013, 12:41 pm

my engine bay

my buddys klze-t

kulluminati777 · Post by **kulluminati777** » February 14th, 2013, 2:37 pm

I KNOW THAT BAY ANYWHERE!!YOUR BUDDY OWNS THE LEGENDARY "GOLDMEMBER"!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

does it have a mazdaspeed front? If so thats goldmember. A legendary car sold a few years ago by a member who built it. If it is thats not a KLZE-T its a KLG4-T which is even better

Sleeper6 · Post by **Sleeper6** » February 14th, 2013, 2:45 pm

That second bay, isnt that goldmembers old car?

**edit** kulimination beat me to it

MazdaMan1991 · Post by **MazdaMan1991** » February 14th, 2013, 3:47 pm

It's a ZE block with a G4 top end built from ground up and yes it has the mazdaspeed front
Blown 3 sets of rods and blew 2 trannys

boooooost.
He built the motor in his kitchen using performance everything lol his name is Brandon and I heart his mx3 lol

kulluminati777 · Post by **kulluminati777** » February 14th, 2013, 4:05 pm

lovely!

Ok so I guess KL-Z4 should be the new proper term lol

MazdaMan1991 · Post by **MazdaMan1991** » February 14th, 2013, 4:22 pm

Sounds about right and untuned its a corvette killer theres a couple vids of it on my YouTube page

kulluminati777 · Post by **kulluminati777** » February 14th, 2013, 4:38 pm

oh i believe it i have seen the car in action on videos before. Perfectly built MX3

RobMinhas · Post by **RobMinhas** » February 14th, 2013, 6:15 pm

Don't ZEs and G4s both have the same top end(as in heads and cams) just a different block and intake manifold?

MazdaMan1991 · Post by **MazdaMan1991** » February 15th, 2013, 7:35 am

RobMinhas wrote:Don't ZEs and G4s both have the same top end(as in heads and cams) just a different block and intake manifold?

Nope, if I'm not mistaken millenias have the same heads

WhiteFinish · Post by **WhiteFinish** » February 15th, 2013, 11:39 am

G4's are very different from other KL heads

youdirtyfox · Post by **youdirtyfox** » February 15th, 2013, 12:05 pm

Dont think I have posted in this topic before, so.......

MazdaMan1991 · Post by **MazdaMan1991** » February 15th, 2013, 12:41 pm

youdirtyfox wrote:Dont think I have posted in this topic before, so.......

hows the setup coming?

RX8SE3P · Post by **RX8SE3P** » February 15th, 2013, 4:47 pm

This is when I very first swapped.

RX8SE3P · Post by **RX8SE3P** » February 15th, 2013, 4:52 pm

Then I changed the intake after rebuilding, still pretty hard to fit it.

Currently swapping to curved neck and entirely different intake. Will post pics later!

MX-3.com

Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!

Re: Let's see your engine bays!!