[FS]: UDP, Redtops w/ rails, ZE Disty, KL31 Cams, etc..

[EZ_4_FUN]

These are left over parts ive collected over the years.. All were pulled in working condition.

All prices in CDN, do not include shipping; paypal is prefered, OBO.


MS8 Intake Manifold (complete)$50 ** SOLD **
Vortech FMU 10:1: $25 ** SOLD **
Unorthodox UDP: $40 ** SOLD **
ZE Distributor: $30 ** SOLD **
ZE CAMS ** SOLD **



Nissan Redtops modded in rails w/ OEM connector: $120
Breather Filter: $5
T3 flange: $7
MSD coil ballast resistor 0.8ohm: $10
Silicone couplers:
3-2.5"coupler
4-2.25" coupler
3-2"coupler
1-2.5"90 DEG coupler
1-3"coupler
2-3/4" to 2-3/8" reducer
3" to 2-1/2" reducer
2-1/2" to 2" reducer
2-3/4"to 2-1/2" reducer: $2.50 each or $25 for all 16 pcs
SONY XPLODE 1200W amp: $60
2.5" Exhaust flange w/ gasket: $10

1995 2.5 ZE Turbo: PM ME.
1995 2.5 ZE Turbo
Thanks for Looking

[bbunkerc397]

I want the ZE distributor, pm'd.

[Evo_Spec]

i'd like some couplers, pm'd

*edit* read the sizes wrong and realized i don't need them

[Daninski]

How about a little history on the engine set up?

[Sleeper6]

I want the ZE distributor, pm'd.

seconds if bbunker backs out

[MrMazda92]

I'm interested in the UDP.

How minty is it? The picture looks good, but it's only one angle. I need to verify 100% that UDPs are coilpack friendly, I believe I can make it a 6-1 trigger wheel, if I'm not mistaken... If that is the case, I'll paypal you same day.

[EZ_4_FUN]

Its pretty Mint. PM me your email, and I will send you more photos of it.

I'm interested in the UDP.

How minty is it? The picture looks good, but it's only one angle. I need to verify 100% that UDPs are coilpack friendly, I believe I can make it a 6-1 trigger wheel, if I'm not mistaken... If that is the case, I'll paypal you same day.

[kulluminati777]

If the UDP fits a N/A ZE with no issues ill take it if mrmazda doesnt want it

[MrMazda92]

PM'd my email

[MrMazda92]

I haven't gotten an email yet(checked spam filter), but I'm still definitely interested in the pulley. I've got funds ready, pending pictures!

[kulluminati777]

lol it was like a day between the two posts saying u wanted it and then saying no reply to u

[EZ_4_FUN]

Hi all,

Hang tight. I have a few requests. The weather is shitty around here. I will get the shipping info and pictures b4 the weekend.

I want and need to get rid of this stuff, so im on top of all req's!

[Ryan]

I'm next on the UDP if MM doesn't take it.

Just email me instead, I don't check in here too often anymore. ryan dot thomson dot mx at gmail dot com.

[MrMazda92]

Ryan, missed ya buddy! Where've you been hiding out? Some Mx-5 forum? Tisk tisk! You can never escape the call of the MX-3.

I'm about 99% on the UDP, sorry to burst everybody's bubbles! It looks good, I just want to be positive, even though I'll have it balanced with the rest of my rotating assembly.

[MrMazda92]

Alright, I'll take the UDP.

I just noticed shipping isn't included, do you have an approx. quote to 97402 in the states? It'll probably be $7-10, I imagine.

As soon as I know, I'll paypal you!

PM'd the same