RS_OBD'oh_2's 1996 RS + T

In this section, Users can post worklogs for their vehicle and show users their projects. (MX-3 ONLY!). Please create only ONE topic when starting a project, and DO NOT create 2 worklogs for the same vehicle, even though they are different projects. READ THE STICKY!
User avatar
RS_OBD'oh_2
Senior Member
Posts: 2400
Joined: April 9th, 2007, 1:26 pm
Location: Calgary, AB

Re: RS_OBD'oh_2's 1996 RS + T

Post by RS_OBD'oh_2 »

It is in fact still an F series.

Clutch is a Spec 2+. I will be swapping in the future, but don't see any outside the box issues for the OBDII.
User avatar
RS_OBD'oh_2
Senior Member
Posts: 2400
Joined: April 9th, 2007, 1:26 pm
Location: Calgary, AB

Re: RS_OBD'oh_2's 1996 RS + T

Post by RS_OBD'oh_2 »

in the process of moving the batter just a bit. Had to modify the base and a new battery tied down.

There were issues with the old tie down hitting the intercooler pipe.
Image
Image
I picked up a password JDM civic tie down, some modification was needed.
Image
Here is the trimmed battery tray. I removed the old anchor, cut it and attached in a new location.
Image
Image
The red rubber washer and wing nut are just for the initial test fitting.
I will be mounting the other side of the tie down to the CS strut bar
Image
More to come...
User avatar
RS_OBD'oh_2
Senior Member
Posts: 2400
Joined: April 9th, 2007, 1:26 pm
Location: Calgary, AB

Re: RS_OBD'oh_2's 1996 RS + T

Post by RS_OBD'oh_2 »

have battery tie close to complete... was finally able to use my tap and die set.

Image

Still have to find a good switch solution to use the onboard voltmeter.

Image
User avatar
RS_OBD'oh_2
Senior Member
Posts: 2400
Joined: April 9th, 2007, 1:26 pm
Location: Calgary, AB

Re: RS_OBD'oh_2's 1996 RS + T

Post by RS_OBD'oh_2 »

She's legal now!!!
Finally got the Reg done, gas and a quick wash.

Image
Image
Image
User avatar
Calg_93GS
Regular Member
Posts: 192
Joined: July 6th, 2011, 11:40 am
antispam: ~SPAM*SUX~
Location: Calgary AB

Re: RS_OBD'oh_2's 1996 RS + T

Post by Calg_93GS »

:2thumbsup: lookin good
Worklog
Image
:: DIY CAI :: DIY Ground kit + Condenser :: Euro Mini Sides :: SE Leather Seats :: Kenwood Headunit w/ Custom IPod Mount ::
:: KYB GR2 w/ H&R Springs :: Drag DR-2 17x7 :: RS Raised Spoiler :: 2x12" Polk DB1222 subs w/ 800w Clarion amp ::
User avatar
Evo_Spec
Senior Member
Posts: 2504
Joined: December 30th, 2008, 3:41 am
Location: Calgary, Alberta, Canada

Re: RS_OBD'oh_2's 1996 RS + T

Post by Evo_Spec »

looks great man! did you ever install the......power steering reservoir?

this puts a little pressure on me to get mine legal too....
User avatar
RS_OBD'oh_2
Senior Member
Posts: 2400
Joined: April 9th, 2007, 1:26 pm
Location: Calgary, AB

Re: RS_OBD'oh_2's 1996 RS + T

Post by RS_OBD'oh_2 »

naw man. Been too busy. Looks like I'll need more power steering rated hose to get it where I want it.
User avatar
Tavman_1213
Regular Member
Posts: 412
Joined: September 2nd, 2011, 6:13 pm
antispam: ~SPAM*SUX~
Location: Calgary, AB, Canada

Re: RS_OBD'oh_2's 1996 RS + T

Post by Tavman_1213 »

Looks great!! Hope to see the car in person sometime soon!!
93 White RS- BPT Built not bought!!
Worklog: viewtopic.php?f=46&t=78988
User avatar
RS_OBD'oh_2
Senior Member
Posts: 2400
Joined: April 9th, 2007, 1:26 pm
Location: Calgary, AB

Re: RS_OBD'oh_2's 1996 RS + T

Post by RS_OBD'oh_2 »

Now that Mike is up and running we should all go for a cruze, or at least a mini meet.
User avatar
Tavman_1213
Regular Member
Posts: 412
Joined: September 2nd, 2011, 6:13 pm
antispam: ~SPAM*SUX~
Location: Calgary, AB, Canada

Re: RS_OBD'oh_2's 1996 RS + T

Post by Tavman_1213 »

RS_OBD'oh_2 wrote:Now that Mike is up and running we should all go for a cruze, or at least a mini meet.
A mini meet would be great. What would make it better would be if it was at my house that why I could feel involved since my car is far from drivable haha jk.
93 White RS- BPT Built not bought!!
Worklog: viewtopic.php?f=46&t=78988
User avatar
Evo_Spec
Senior Member
Posts: 2504
Joined: December 30th, 2008, 3:41 am
Location: Calgary, Alberta, Canada

Re: RS_OBD'oh_2's 1996 RS + T

Post by Evo_Spec »

Tavman_1213 wrote:
RS_OBD'oh_2 wrote:Now that Mike is up and running we should all go for a cruze, or at least a mini meet.
A mini meet would be great. What would make it better would be if it was at my house that why I could feel involved since my car is far from drivable haha jk.
lols!
User avatar
RS_OBD'oh_2
Senior Member
Posts: 2400
Joined: April 9th, 2007, 1:26 pm
Location: Calgary, AB

Re: RS_OBD'oh_2's 1996 RS + T

Post by RS_OBD'oh_2 »

not a real update... but something new on order:

Image

will be selling the eibach/hp setup soon
User avatar
Tavman_1213
Regular Member
Posts: 412
Joined: September 2nd, 2011, 6:13 pm
antispam: ~SPAM*SUX~
Location: Calgary, AB, Canada

Re: RS_OBD'oh_2's 1996 RS + T

Post by Tavman_1213 »

Sorry I got impatient an ordered my suspension!! Otherwise I would have bought yours!! Besides now I can say Mike is jelious of my "booty" hahaha
93 White RS- BPT Built not bought!!
Worklog: viewtopic.php?f=46&t=78988
User avatar
Evo_Spec
Senior Member
Posts: 2504
Joined: December 30th, 2008, 3:41 am
Location: Calgary, Alberta, Canada

Re: RS_OBD'oh_2's 1996 RS + T

Post by Evo_Spec »

nice....
User avatar
RS_OBD'oh_2
Senior Member
Posts: 2400
Joined: April 9th, 2007, 1:26 pm
Location: Calgary, AB

Re: RS_OBD'oh_2's 1996 RS + T

Post by RS_OBD'oh_2 »

did some painting with Mike today. Bumper has been finally painted with the the good stuff.

Image
Post Reply

Return to “MX-3 Worklogs”