GC's On ZX2 struts
-
Thefez
- Regular Member
- Posts: 423
- Joined: September 26th, 2011, 6:30 am
- antispam: ~SPAM*SUX~
- Location: USA,PA
GC's On ZX2 struts
Ok so as some might have seen I put my GC's on ZX2's up for sale because of the gap between the springs and strut tops boths me.. I've been reading about "preloads" or "Helper Spring". This looks like if I could find a cheap set of these i'd keep my GC's on ZX2's
-
Josh
- Supporting Member
- Posts: 3432
- Joined: April 18th, 2002, 2:01 am
- Location: Washington state
- Contact:
Re: GC's On ZX2 struts
There are several places you can buy either. H&R is probably your best bet, but you will have to call them as they do not list them on their site. The set of 4 with perches ran me about 250.
Josh
95' AWD MX-3 RST - (work log - http://www.mx-3.com/phpBB3/viewtopic.php?f=46&t=73765 )
94' GS - KLZE DD (work log - viewtopic.php?uid=2713&f=46&t=79063&start=0 )
05' MS RX-8 - Parted out and Sold :'(
Feedback - http://www.mx-3.com/phpBB3/viewtopic.php?f=37&t=49519
Cardomain Page - http://www.cardomain.com/ride/408020
Face Book page http://www.facebook.com/pages/Mazda-MX- ... 3472959216
95' AWD MX-3 RST - (work log - http://www.mx-3.com/phpBB3/viewtopic.php?f=46&t=73765 )
94' GS - KLZE DD (work log - viewtopic.php?uid=2713&f=46&t=79063&start=0 )
05' MS RX-8 - Parted out and Sold :'(
Feedback - http://www.mx-3.com/phpBB3/viewtopic.php?f=37&t=49519
Cardomain Page - http://www.cardomain.com/ride/408020
Face Book page http://www.facebook.com/pages/Mazda-MX- ... 3472959216
-
Thefez
- Regular Member
- Posts: 423
- Joined: September 26th, 2011, 6:30 am
- antispam: ~SPAM*SUX~
- Location: USA,PA
Re: GC's On ZX2 struts
What info did they need from you? and what other places can I buy them from options are goodJosh wrote:There are several places you can buy either. H&R is probably your best bet, but you will have to call them as they do not list them on their site. The set of 4 with perches ran me about 250.
250 isn't bad at all just kinda wana see other quality/price options-
mikeinaus
- Regular Member
- Posts: 1751
- Joined: November 2nd, 2009, 3:03 am
- antispam: No
- Location: Vancouver, BC
Re: GC's On ZX2 struts
you shouldnt need the preloads. dont get me wrong its probably nice to have them but there not necessary. solo_ryder ran ground controls on zx2 struts for years without preloads and never had problems.
-
Thefez
- Regular Member
- Posts: 423
- Joined: September 26th, 2011, 6:30 am
- antispam: ~SPAM*SUX~
- Location: USA,PA
Re: GC's On ZX2 struts
Theres a ton of guys that run them on zx2's without them but i want them for my peice of mind.mikeinaus wrote:you shouldnt need the preloads. dont get me wrong its probably nice to have them but there not necessary. solo_ryder ran ground controls on zx2 struts for years without preloads and never had problems.