In this section, Users can post worklogs for their vehicle and show users their projects. (MX-3 ONLY!). Please create only ONE topic when starting a project, and DO NOT create 2 worklogs for the same vehicle, even though they are different projects. READ THE STICKY!
Last edited by Ryan on June 7th, 2011, 3:56 pm, edited 1 time in total.
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped. Feedback
that crank will have to be polished. You won't be able to size the replacement bearing properly unless you do.
94' RS/GS/MS/CF Monster Turbo...coming soon.
93' GS SE, the Black Beast, the former love of my life...soon to be gutted and crushed.
94' GS, black on black, now in several small pieces...and one large crushed piece.
2007 Mazda3 GT Sport --- super fun
2004 Honda RC51 --- Lost forever to some theavin' bastard My Worklog My feedback thread Never attribute to malice that which can be adequately explained by stupidity.
Yeah, bearings are cheap, but how bad is the crank??? Is that a gouge (sorry for spelling) carved into the crank journal???? Kind of hard to tell in the picture.
1992 MX3 GS (My Project Toy)
K8DE, see web site...too many mods to list, but still growing.
2006 Dodge Durango (The Family-Mobile) Every time you race a Honda Civic, a kitten kills a retard.
Thanks wyt. 2000+ grit sandpaper here I come. Plastigauge too.
Its not bad, It doesn't catch my fingernail at all, not even close. I just ordered standard size for now, I hope they're good enough. This is my DD, so I'm just assuming for now, because there's a chance they'll still be in spec.
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped. Feedback
Ordered the bearings, they'll be here tomorrow around noon, bought some plastigauge (green) and sandpaper...
So far teh rest of them look good, but I'm obviously goin to replace them all.
I'm thinking debris played a role... there are some strange wear/splotch marks on some of the bearings.
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped. Feedback
Rod 5
2 hours of polishing w/ 2k grit: you can see the good #6 in the background.
Rod 6
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped. Feedback
The front main bearing looks like it has chunks of aluminum welded to it, so I'm going to just call this a debris issue.
I'm getting the crank reground, new bearings, new oil pump, and heaven help this motor if it takes a s--- then...
The cylinder walls look pretty dang shiny though
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped. Feedback
some pretty major scoring on the top of #5 that I couldn't see with the block together:
the weird pitted/welded #1 main bearing
A cylinder wall
$120 to regrind all the journals, plus bearings, so this is about a $250 +15 hour mistake.
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped. Feedback
Good call pulling the crank. I didn't want to sound like a know it all...but trying to just clean up that journal by hand and putting it back together was a recipe for another disaster.
So was the crank initially ground 0.010" under? Are they taking another 0.010" off or is it just a quick polish? do you have micrometers? I would be checking and double checking journal diameters. If it was already 10 thou under and they're polishing it again, you could wind up 14-15 thou under. In which case you'd basically have to go to 20 under to fit the next undersize bearing.
Definitely check it.
94' RS/GS/MS/CF Monster Turbo...coming soon.
93' GS SE, the Black Beast, the former love of my life...soon to be gutted and crushed.
94' GS, black on black, now in several small pieces...and one large crushed piece.
2007 Mazda3 GT Sport --- super fun
2004 Honda RC51 --- Lost forever to some theavin' bastard My Worklog My feedback thread Never attribute to malice that which can be adequately explained by stupidity.
I just checked some stuff with plastigauge, the mains are good on the oil pump side and progressively get worse to the flywheel side, which makes sense. They were all in spec, though.
Only done rod 6 and 5, 6 is a bit low, 5 is too low.
my machinist is actually meeting me after hours on his way to somewhere else so I can just drop the crank off with him and they'll check it out. I think I want to just grind it down so I can have exactly the tolerances I want (a little tighter than stock).
Its only $120 to do all 10 journals, plus another $120ish for bearings... turns into a $300 mistake, but now its upgraded from stock. Even if I decided to machine it down in the first place, it would have cost me this $120 (could have specified bearing size in the rebuild kit from topline)
so in reality, I'm only out $120 which is good considering what the damage could have been.
Edit, checked them all... they're all right on the edge(aside from #5 which is over), in the neighbourhood of 0.04mm
Last edited by Ryan on June 10th, 2011, 6:19 pm, edited 1 time in total.
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped. Feedback
Knife edge would require another balance (including heavy metals) and that would be at least another $400, so thats out of the question. Its already balanced.
Plus, if I were to drastically modify the crank, I'd actually turn it into a raindrop shape... Nature has all of the best designs, if you haven't thought about it.
Final diagnosis:
borderline clearances
dirty break in oil (on its 2nd batch, but still looked like rheomag fluid)
debris in the oil passages (from boring them out)
Perhaps oil pump.
Main #1 was pitted like the picture, and #2 less, and #3 less, and #4 less, so I call dirty oil on that.
Main #1 was perfectly clearanced, linear down to #4, which was a bit on the loose side, but acceptable.
all rod bearings were on the loose side, #5 was over (likely only from being spun/polished).
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped. Feedback