Sam's 1.6 MX-3- LT Turbo project.

youdirtyfox · Post by **youdirtyfox** » January 15th, 2011, 5:34 am

fillpereira wrote:That looks awesome, why hasnt this been done before lol

because no-one has my imagination, mwhahahahaha

youdirtyfox · Post by **youdirtyfox** » January 26th, 2011, 12:48 pm

grill meshing the hole was a mare!
so instead the siliocon tubing has gone
around the bumper and new grill mesh
is being bought to go behind and fixed
to the back of the bumper.

in the meantime have started work
on a wind splitter made from 5mm plastic

also need to get a drivers side headlight
as mine has a crack, before I fit this lot up.
few more weeks waiting yet!

AaronTietje · Post by **AaronTietje** » January 26th, 2011, 2:28 pm

Your doing a great job. I look forward to seeing it on the car.

youdirtyfox · Post by **youdirtyfox** » February 4th, 2011, 12:38 pm

should be on next weekend

youdirtyfox · Post by **youdirtyfox** » February 12th, 2011, 8:59 am

Savin · Post by **Savin** » February 12th, 2011, 9:41 am

I think it'd look pretty badass if you do the angry-eye mod too!

fillpereira · Post by **fillpereira** » February 12th, 2011, 10:51 am

Turned out great, good job man

youdirtyfox · Post by **youdirtyfox** » February 12th, 2011, 10:58 am

Savin wrote:I think it'd look pretty badass if you do the angry-eye mod too!

No one over here does that anymore!

Very pleased with it myself,
just need to 'flex' the splitter
down a bit with its support rods

Sleeper6 · Post by **Sleeper6** » February 12th, 2011, 11:06 am

How about a custom headlamp with an airduct to complete the look?

AaronTietje · Post by **AaronTietje** » February 12th, 2011, 11:45 am

Very impressive. Great work and good vision.

youdirtyfox · Post by **youdirtyfox** » February 12th, 2011, 12:05 pm

Sleeper6 wrote:How about a custom headlamp with an airduct to complete the look?

This is my daily driver, so that would have to be 'tr5ackday special'
thing.

Thanks Aaron, appreciate your comments

youdirtyfox · Post by **youdirtyfox** » February 18th, 2011, 12:13 pm

test fitted up my 25mm spacers.

located with 54.1 > 67.1 spigot ring

Too wide on the front without loads of negy camber

just inside with negy camber

going to have to arch roll or turn the spacers down a bit...to pass MOT laws
Rears are in, just!

wheels are 15 x 7 et35 195/50/15's btw
Took the fronts back off till I decide what to do with 'em

p.s. and please no spacer bashing I know the deal

weede_klze · Post by **weede_klze** » February 19th, 2011, 5:01 am

looks great man!

youdirtyfox · Post by **youdirtyfox** » February 20th, 2011, 4:20 am

Thanks Weede

She'll look even better if I can fuse these
new mirrors of mine to original base plates !

Dragon1212 · Post by **Dragon1212** » February 23rd, 2011, 12:50 pm

That looks Really good... its not like some of them that have holes everywhere and a massive one in the middle...

MX-3.com

Sam's 1.6 MX-3- LT Turbo project.

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project

Re: UK Sam's 1.6 Turbo MX-3 project