HELP!!! BOV & W/G question???

[johnmx3ze]

hi i received my turbo kit yesturday and the something that i dont understand with my BOV and my W/G why do i have 2 niples on each of them???
and how do i run my hoses?

[marcdh]

I don't know much about turbos errr doesn't the wastegate have the waste exhaust exit (to screamer pipe or back in to exhaust past turbo exit). And another for boost controller?

[kab-rst]

you use only the top of each niple

the second one is used to make them react faster(bov will open/close faster with it routed to the second one) but i dont exactly remmeber how to route the second one.

in any case, i'm only using one of em on my bov/wg and everything goes well

[johnmx3ze]

ok thx but do i have to block the other nipple on the w/g and bov?

[kab-rst]

nop, the wastegate will be self blocked when u'll tight the bolt on, the bov dont requires anything

[hppwdn]

nop, the wastegate will be self blocked when u'll tight the bolt on, the bov dont requires anything

This is not accurate. The wastegate uses banjo bolts. It does not "self block." The top port is for electronic boost controllers to reapply pressure to keep the wastegate shut. If you don't have an ebc the top nipple can be left open, or not even installed.

The side port is your source for boost reference from your intake manifold. That one pushes open the spring as the psi increases. For non boost controller and manual boost controller applications this is the only one you have to use.

Tial install info for reference
http://www.tialmedia.com/documents/w3_t ... nstall.pdf" onclick="window.open(this.href);return false;

With the BOV, I'm not sure, don't know too much about that type. I have a Tial 50mm bov.

[kab-rst]

nop, the wastegate will be self blocked when u'll tight the bolt on, the bov dont requires anything

This is not accurate. The wastegate uses banjo bolts. It does not "self block." The top port is for electronic boost controllers to reapply pressure to keep the wastegate shut. If you don't have an ebc the top nipple can be left open, or not even installed.

The side port is your source for boost reference from your intake manifold. That one pushes open the spring as the psi increases. For non boost controller and manual boost controller applications this is the only one you have to use.

Tial install info for reference
http://www.tialmedia.com/documents/w3_t ... nstall.pdf" onclick="window.open(this.href);return false;

With the BOV, I'm not sure, don't know too much about that type. I have a Tial 50mm bov.

thanks for corecting me. as for the BOV, i was using a greedy type-s with 2 nipple(didin'thad to use the lower one on mine) as i changed to an hks, i have only one nipple on the ssqv,

[johnmx3ze]

thx guys really appreciated and could someone help me i have a cheap boost controller that came in my kit but i have not idea how to hook it up? because i have a 3.6 psi spring in my w/g and i wanna put it up to around 5 psi...?

[Bo0sted_Rafi]

In a WG, you use the top nipple if you got a manual or electronic boost controller.

The correct instalation its when you use a line from the turbo to the wg in the nipple below of the wg. in that line you can use a "T" to use that boost signal to a boost controller and from the boost controller to the upper nipple of the wg. In my case, i got a better response when i use a boost controller.

[johnmx3ze]

In a WG, you use the top nipple if you got a manual or electronic boost controller.

The correct instalation its when you use a line from the turbo to the wg in the nipple below of the wg. in that line you can use a "T" to use that boost signal to a boost controller and from the boost controller to the upper nipple of the wg. In my case, i got a better response when i use a boost controller.

thx i made a lil diagram lol really fast and cheap but its juste to know if this is what you mean??? correct me if that wrong...

ok i tryed posting it on here but i cant so can you give me your email i'll send it to you...