Re-Painting Stock Wheels
-
- Regular Member
- Posts: 1704
- Joined: December 31st, 2005, 5:54 pm
- Location: Burlington + Grimsby, Ontario, Canada
- Contact:
With a 50 gallon copressor and a cheep sandblaster, it took from about 3pm to about now (9:30) including paint drying time to do 1 rim.
I didnt take the tire of the wheel, but that would make it easier.
It would also make it alot easier to get it professionally sandblasted. i think i was quoted about 50 bucks to have it done, but then you have to get the tires off the rim.
to do all 4 rims it would be a full weekend job, if you have your own sandblaster.
Make sure to follow the directions on the paint! DO NOT try to rush the painting. Make sure it has time to dry
My clearcoat takes a full 5 days to dry. but its hard after just 30 mins.
Its ok to put them on the car after about 4 hours of drying, but dont drive it for about 2 or 3 days.
getting it professionaly sandblasted might take a little longer, but might end up with a silightly better quality, although mine turned out perfect.
im just heading downstairs now to take more pictures of the finished product, clearcoat done! il post them to my cardomain page in a few mins.
Bochek
I didnt take the tire of the wheel, but that would make it easier.
It would also make it alot easier to get it professionally sandblasted. i think i was quoted about 50 bucks to have it done, but then you have to get the tires off the rim.
to do all 4 rims it would be a full weekend job, if you have your own sandblaster.
Make sure to follow the directions on the paint! DO NOT try to rush the painting. Make sure it has time to dry
My clearcoat takes a full 5 days to dry. but its hard after just 30 mins.
Its ok to put them on the car after about 4 hours of drying, but dont drive it for about 2 or 3 days.
getting it professionaly sandblasted might take a little longer, but might end up with a silightly better quality, although mine turned out perfect.
im just heading downstairs now to take more pictures of the finished product, clearcoat done! il post them to my cardomain page in a few mins.
Bochek
- fry_81
- Regular Member
- Posts: 1898
- Joined: April 22nd, 2004, 2:01 am
- Location: Barrie, Ontario, Canada
- Contact:
very nice job. i redid my gs rims not too long ago, just in bronze. ![2 Thumbs Up :2thumbsup:](./images/smilies/2thumbsup.gif)
![2 Thumbs Up :2thumbsup:](./images/smilies/2thumbsup.gif)
1994 5spd GS Parts Car For Sale 800obo. e-mail for details. fry_81@hotmail.com
- Josh
- Supporting Member
- Posts: 3432
- Joined: April 18th, 2002, 2:01 am
- Location: Washington state
- Contact:
thoes look sweet. not too long ago someone posted some that they painted gunmetal with a polished lip. great job! they look better than new
Josh
95' AWD MX-3 RST - (work log - http://www.mx-3.com/phpBB3/viewtopic.php?f=46&t=73765 )
94' GS - KLZE DD (work log - viewtopic.php?uid=2713&f=46&t=79063&start=0 )
05' MS RX-8 - Parted out and Sold :'(
Feedback - http://www.mx-3.com/phpBB3/viewtopic.php?f=37&t=49519
Cardomain Page - http://www.cardomain.com/ride/408020
Face Book page http://www.facebook.com/pages/Mazda-MX- ... 3472959216
95' AWD MX-3 RST - (work log - http://www.mx-3.com/phpBB3/viewtopic.php?f=46&t=73765 )
94' GS - KLZE DD (work log - viewtopic.php?uid=2713&f=46&t=79063&start=0 )
05' MS RX-8 - Parted out and Sold :'(
Feedback - http://www.mx-3.com/phpBB3/viewtopic.php?f=37&t=49519
Cardomain Page - http://www.cardomain.com/ride/408020
Face Book page http://www.facebook.com/pages/Mazda-MX- ... 3472959216
-
- Regular Member
- Posts: 1704
- Joined: December 31st, 2005, 5:54 pm
- Location: Burlington + Grimsby, Ontario, Canada
- Contact:
Actually they look exaclty like new, as far as the eye can tell. and the greatest part, it was just crylon spray paint, dull aluminum. $4.50 a can at canadian tire.
One can is MORE then enough to do all the wheels.
You also need a can of clear coat. I used motormaster clear enamal $7.50 a can @ canadian tire
Unfortunatly after getting that wheel done my compressor went KAPUT and nolonger runs, tracked the problem down to a blown capicitor on the motor. Stores arn't open today so hopefully il get one tomorow. Damn.
Anyways, back to dreaming on what upgrades i deffently cant afford to do to my mx-3
Bochek
One can is MORE then enough to do all the wheels.
You also need a can of clear coat. I used motormaster clear enamal $7.50 a can @ canadian tire
Unfortunatly after getting that wheel done my compressor went KAPUT and nolonger runs, tracked the problem down to a blown capicitor on the motor. Stores arn't open today so hopefully il get one tomorow. Damn.
Anyways, back to dreaming on what upgrades i deffently cant afford to do to my mx-3
Bochek
- GregoryChristian
- Supporting Member
- Posts: 1413
- Joined: March 4th, 2003, 2:01 am
- Location: Gulf Coast
good job , I recently bought a set of gloss black Motegi wheels and after installing them on my car I didn't like the look so I took them off and painted them Argent silver and clear coated them at work
** My MX-3 ** http://www.cardomain.com/ride/360367
-
- Regular Member
- Posts: 184
- Joined: September 19th, 2005, 8:00 pm
- Location: Philomath, Oregon (Hickville, USA)
- Contact:
- fry_81
- Regular Member
- Posts: 1898
- Joined: April 22nd, 2004, 2:01 am
- Location: Barrie, Ontario, Canada
- Contact:
yes, ill upload them tommorow
1994 5spd GS Parts Car For Sale 800obo. e-mail for details. fry_81@hotmail.com
- happyclown
- Regular Member
- Posts: 316
- Joined: July 18th, 2004, 2:01 am
- Location: Vermont
- Contact: