hold light flashing

General Mazda MX-3 Discussions
Post Reply
Neilster
Junior Member
Posts: 4
Joined: September 24th, 2001, 2:01 am
Location: Ontario, Canada

hold light flashing

Post by Neilster »

hello fellow Mazda owners i have a 1992 mx3 v-6 and the hold light keeps coming on i was wondering if any one had a diagnostic tester that i could borrow for a day so i could plug it into my car and read the fault codes so i can find and fix the problem.........or if someone can tell me where i can buy one if i have to but i would rather just borrow one, i dont have alot of money.........Neil
Ramfis Mx3
Regular Member
Posts: 55
Joined: May 12th, 2001, 2:01 am
Location: Puerto Rico

Re: hold light flashing

Post by Ramfis Mx3 »

Tell you what, Same thing happend to me and a few month later my tranny past to better live, so I change my car to manual tranny. :cool:
yeloboy
Regular Member
Posts: 110
Joined: March 11th, 2001, 2:01 am
Location: dallas/san antonio-texas ,usa

Re: hold light flashing

Post by yeloboy »

hey, iv'e had that same problem with mt gs.you need to get it checked out right away.its your trans.most of the time its an electrical transaxle problem. but with mine it was stuck in overdrive witch is'nt good.cause it means your car is leaving in third gear each time you go.it ended up costing me $1700 and that sucked.so get it checked soon :confused:
INFAMOUS YELOBOY
bslenderpeak
Regular Member
Posts: 38
Joined: September 16th, 2001, 2:01 am
Location: Grand Isle, VT US

Re: hold light flashing

Post by bslenderpeak »

Does the car shift in and out of whatever gear your in? EX( whith the shifter in 2nd does it shift from 2nd to 3rd to 2nd or what? I personally think it's just a connection. I had a distributor problem with my 95 4cyl and during testing everything on the car I found with one of the ECM connectors unplugged that the hold light would flash. Plugging the connector back in it was fine. I'm not saying that your ECM connector is the problem, maybe a burned wire, or a little corrosion on the wrong connector ECM, TPS, ATX. I would look up the sections that cover this in the online service manual and troubleshoot it a little further.
'95 Blue Creek Mica RS<BR>Vermont
User avatar
Andrew_Pakula
Senior Member
Posts: 2362
Joined: November 18th, 2000, 2:01 am
Location: Toronto, Ontario, Canada
Contact:

Re: hold light flashing

Post by Andrew_Pakula »

Most of the time if you start seeing your hold light flashing or going on for no reason then that means your tranny is dying or about to die. By this time you are probably noticing problems with the car shifting properly.<BR>For me its a sickening feeling to see it go on cause if it does then it means I am probably going to have to spend a lot of money on a new tranny.
EMPTYPOCKETS
Regular Member
Posts: 68
Joined: July 18th, 2001, 2:01 am
Location: FAIRFIELD CA

Re: hold light flashing

Post by EMPTYPOCKETS »

took mine about three days after the light started blinking to go to s---. now im the proud owner of a 5 speed w/ a stage two clutch the conv. was quiet difficult to me but well worth it in the long run just my 2 cents<P><BR>late
heatherc
Regular Member
Posts: 248
Joined: August 6th, 2001, 2:01 am
Location: da burgh

Re: hold light flashing

Post by heatherc »

does everybody think that (if i ever have a problm with my transmission) that it's smarter to put in the manual? i would rather have a manual, but i'm not going to spend the money to switch it over now....does it cost a lot to do that?<P>heather
-----------------------------------<BR>_/*\_ ¸.·¤**¤·.,¸,.·¤**¤·.<BR>\ M׳/¸.·¤**¤ müÇh LØVê †Ø M¥ m×鮊<BR>/.·*·.\¸.·¤**¤·.,¸,.·¤**¤<BR>-----------------------------------
Post Reply

Return to “General Mazda MX-3”