Finally got the polished manifold installed
Finally got the polished manifold installed
Finally, I got the Outlaw Engineering Thermoblok spacers kit installed.
Got my polished intake installed aswell, along with the rear valvecover.
The front valvecover we didnt dare to install yet, as it was really rusty on the inside. Gonna clean it up good, and install it
well, one pic for you: (gotta find the two I originally posted)
It looks atleast better than stock
nope-mx3
Got my polished intake installed aswell, along with the rear valvecover.
The front valvecover we didnt dare to install yet, as it was really rusty on the inside. Gonna clean it up good, and install it
well, one pic for you: (gotta find the two I originally posted)
It looks atleast better than stock
nope-mx3
Last edited by nope-mx3 on September 22nd, 2005, 2:54 am, edited 1 time in total.
:: 2001 Mazda Mx-5 Sport // 2013 Volvo V40 D2 Momentum ::
- solo_ryder
- Senior Member
- Posts: 6289
- Joined: October 16th, 2004, 2:01 am
- Location: British Columbia
- jschrauwen
- Forum Moderator
- Posts: 6052
- Joined: September 27th, 2003, 2:01 am
- Location: Frankford, Ontario, Canada
- Contact:
Barry, I was planning on doing something similar this winter to my Millennia IM. Was looking at smoothing everything out and removing a lot of the casting burrs in preparation for powder coating along with the getting my spare set of VC's done the same colour too (a gun metal gray...I think). I didn't know you could get a powder coating in chrome. Were you or had you looked at smoothing the inside of the IM so as to improve air flow and assumably performance?Custommx3 wrote:Im in the middle of polishing my ZE mani at the moment.
Im just gonna have it powder coated in chrome. I've removed all the mill marks and gonna get it to an OK shine just to eliminate any dips and what not.
'92 GS-ZE - sold, '95 GS - sold, '02 Protege LX - Daughter, '00 Audi A4 2.8 QTip, Ducati TT2
90 JDM RHD 300ZX TT - 572.1 RWHP | 590.0 RWTQ | 21 PSI | Pump gas
90 JDM RHD 300ZX TT - 572.1 RWHP | 590.0 RWTQ | 21 PSI | Pump gas
- mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
looking nice
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks
http://www.cardomain.com/id/mitmaks
- ScooterBovine
- Supporting Member
- Posts: 502
- Joined: May 9th, 2004, 2:01 am
- Location: Blacklick, Ohio
- Tunes67
- Supporting Member
- Posts: 4708
- Joined: January 27th, 2005, 6:36 pm
- Location: Everett, WA
- Contact:
That looks pretty sweet man.. I might just have to do something like that to mine eventually.. definately adds to the looks of the engine bay. Cheers
Tunes67
Tunes67
"So long.. and thanks for all the fish!" "Momma says VW Bugs are the devil" "This one time at band camp.. I stuck a flute in my Throttle Body"
"Screw you guys.. I am goin home"
I am the Cranky God of Mods!!! Tremble before my fury!! LOL
"Screw you guys.. I am goin home"
I am the Cranky God of Mods!!! Tremble before my fury!! LOL