i need help on this one... i just installed a new cold air intake for the 90-93 integra on my car...
itll stay on for a few seconds then shuts off... i have all the hoses on and everything i want to know what the deal is
cold air intake, and my car turning off?
- misfitsfiend
- Regular Member
- Posts: 150
- Joined: September 24th, 2004, 2:01 am
- Location: Canada, Toronto west end
- Contact:
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
did you hook your VAF back up?
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
- misfitsfiend
- Regular Member
- Posts: 150
- Joined: September 24th, 2004, 2:01 am
- Location: Canada, Toronto west end
- Contact:
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
the part that moves needs to be facing to the filter so it moves back with incoming air and it needs to be pluged in
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
I had the exact same problem. If you do not find a way to mount your intake so it stays up it pushes the sensor open and the car will shut off. I still didn't figure out a way to hold mine up it just does what it wants to do when it wants to do it. But it may sound stupid but i would probably recommend zip tieing it i just haven't gotten around to doing mine yet. Good luck man!