sealing altezzas (faq?)
-
- Regular Member
- Posts: 733
- Joined: January 16th, 2001, 2:01 am
- Location: Niagara Falls, Canada
- Contact:
sealing altezzas (faq?)
Okay, so I got my lovely x3 racing altezzas, and am going to install them wednesday properly. So I heard that virtually everyone has problems with condensation and water drops getting inside the lens. SO...where exactly do I seal. Around the entire seem, I would guess. I was thinking of using some clear waterproof outdoor silicone. Any ideas? Im going to take some pics of this procedure as simple as it is and post soon... later,
Tom Alexander
93 MX3 GSR - KLZE / stage 3 clutch / PRM Intake / 2.25" exhaust - dual 3" outlet
full custom black and red interior / KLZE ECU / JE50 VAF
http://home.cogeco.ca/~mx3/ - updated dec 1/03
93 MX3 GSR - KLZE / stage 3 clutch / PRM Intake / 2.25" exhaust - dual 3" outlet
full custom black and red interior / KLZE ECU / JE50 VAF
http://home.cogeco.ca/~mx3/ - updated dec 1/03
-
- Senior Member
- Posts: 2053
- Joined: January 1st, 2001, 2:01 am
- Location: Woodbridge, VA, USA
- Contact:
Re: sealing altezzas (faq?)
Every point where the clear lens connects to the black plastic should be sealed. I dont think you need to do the entire thing. Clear silicone will be fine.
Shaun Newman
SOLD 1994 Blaze Red GS/ SOLD 1994 Chaste White GS-R
SOLD 1994 Blaze Red GS/ SOLD 1994 Chaste White GS-R
-
- Regular Member
- Posts: 733
- Joined: January 16th, 2001, 2:01 am
- Location: Niagara Falls, Canada
- Contact:
Re: sealing altezzas (faq?)
okay, I'll give that a try.
Tom Alexander
93 MX3 GSR - KLZE / stage 3 clutch / PRM Intake / 2.25" exhaust - dual 3" outlet
full custom black and red interior / KLZE ECU / JE50 VAF
http://home.cogeco.ca/~mx3/ - updated dec 1/03
93 MX3 GSR - KLZE / stage 3 clutch / PRM Intake / 2.25" exhaust - dual 3" outlet
full custom black and red interior / KLZE ECU / JE50 VAF
http://home.cogeco.ca/~mx3/ - updated dec 1/03
-
- Senior Member
- Posts: 2053
- Joined: January 1st, 2001, 2:01 am
- Location: Woodbridge, VA, USA
- Contact:
Re: sealing altezzas (faq?)
that really doesnt make sense to me so ill refraise...<p>everywhere there are plastic tabs sliding into the black backing should be done. You can probably see the holes if you look at them.
Shaun Newman
SOLD 1994 Blaze Red GS/ SOLD 1994 Chaste White GS-R
SOLD 1994 Blaze Red GS/ SOLD 1994 Chaste White GS-R
Re: sealing altezzas (faq?)
I used silocone in the winter and in hasen't leaked yet
should work
should work
-
- Regular Member
- Posts: 733
- Joined: January 16th, 2001, 2:01 am
- Location: Niagara Falls, Canada
- Contact:
Re: sealing altezzas (faq?)
i bought silicone today and am going to do it and take pics...maybe post them in the next couple...
Tom Alexander
93 MX3 GSR - KLZE / stage 3 clutch / PRM Intake / 2.25" exhaust - dual 3" outlet
full custom black and red interior / KLZE ECU / JE50 VAF
http://home.cogeco.ca/~mx3/ - updated dec 1/03
93 MX3 GSR - KLZE / stage 3 clutch / PRM Intake / 2.25" exhaust - dual 3" outlet
full custom black and red interior / KLZE ECU / JE50 VAF
http://home.cogeco.ca/~mx3/ - updated dec 1/03