What engine do I have?
What engine do I have?
My friend and I are trying to replace the engine in my son's 92 MX-3. I purchased what I thought was a K series 2.5 engine from a bankrupt auction. This engine has a ford valve cover, so I assumed it came out of a Probe. Well when we started to install it in my son's car we had to change the flywheel and the IM is a straight neck, not curved like the K8 we just removed. The serial number on the engine is K8 289020 and K8101 and K81A1 are on the heads. Anyone got any idea what kind of engine this is?
Re: What engine do I have?
Pretty sure that's a klde...a probe/mx-6 engine. 164hp. How much did you pay?
'92 MX-3 KLZE
'04 Subaru STI
'04 Subaru STI
- bmwm3guy
- Regular Member
- Posts: 1066
- Joined: March 7th, 2004, 2:01 am
- Location: Gatineau, QC
- Contact:
Re: What engine do I have?
I believe waht you purchased was a KLDE, or the American version of the KLZE, it is found in Probes and has 164hp. Due to the lower compression ratios, people tend to go the forced induction route while modifying it.... hehehe Im just whispering ideas into your head :p
-
- Forum Moderator
- Posts: 3415
- Joined: September 3rd, 2002, 2:01 am
- Location: Eastern Hemisphere
- Contact:
Re: What engine do I have?
you have a 2.5 klde from the ford probe
08 Infiniti G37s 6speed (The Daily)
Stillen Cold Air Intake, Z1 Plenum Power Mod, Z1 Headers, Z1 Test Pipe, OBX (Ark) Exhaust, Up-Rev Osiris Engine Management (Tuned at Z1), 20x9" 20x10" Str Racing Concave Staggered Rims, SPC Camber kit, Tein H Techs Springs
01 Lexus Is300 (LS2 Project)
93 Mx3 SE 2.5 KLZE (sold it)
93 Mx3 GS 2.0 KFZE (killed it)
Stillen Cold Air Intake, Z1 Plenum Power Mod, Z1 Headers, Z1 Test Pipe, OBX (Ark) Exhaust, Up-Rev Osiris Engine Management (Tuned at Z1), 20x9" 20x10" Str Racing Concave Staggered Rims, SPC Camber kit, Tein H Techs Springs
01 Lexus Is300 (LS2 Project)
93 Mx3 SE 2.5 KLZE (sold it)
93 Mx3 GS 2.0 KFZE (killed it)
- PATDIESEL
- Senior Member
- Posts: 4476
- Joined: August 13th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Atlanta, GA.
Re: What engine do I have?
You can use the 1.8 intake I you need to. It will give you less HP, but will be an easier fit and all you have to do is hook up the vaccum lines the way you took them off.
![Image](http://www.patdiesel.atlantamx3.com/MX-3/patdieselsigMX-3.jpg)
ZE -strait neck,headers,2.5 exhaust,pheno spacers,lower cross member,GC coils,MS struts,Brembo slotted rotors,filled MS mounts,SS brake/clutch lines, CAI,to rear bat reloc,Hella headlamps,Hella DE fogs 180WHP
- Custommx3
- Site Administrator
- Posts: 8391
- Joined: November 7th, 2000, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Lat 35.1N Lon -90W
- Contact:
Re: What engine do I have?
you probably have a K8 with KL intake manifold and KL vavle cover.
if it was a KL it'd say KL101 not k8.
if it was a KL it'd say KL101 not k8.
- papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
Re: What engine do I have?
what about a KF-ZE? didnt some of them come out of ford cars too?
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
- atlantamx3
- Supporting Member
- Posts: 2888
- Joined: June 2nd, 2001, 2:01 am
- Location: Kennesaw, Ga, USA
- Contact:
Re: What engine do I have?
NO.what about a KF-ZE? didnt some of them come out of ford cars too?
- Custommx3
- Site Administrator
- Posts: 8391
- Joined: November 7th, 2000, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Lat 35.1N Lon -90W
- Contact:
Re: What engine do I have?
YES! They did.
MS-6
Eunos500
MS-8
MX-6
Clef
Ford Telstar
Lantis
XEDOS6
But the KF, even though it has a version of k8 heads, it reads KF on the block.
![Smile :)](./images/smilies/icon_smile.gif)
MS-6
Eunos500
MS-8
MX-6
Clef
Ford Telstar
Lantis
XEDOS6
But the KF, even though it has a version of k8 heads, it reads KF on the block.
- atlantamx3
- Supporting Member
- Posts: 2888
- Joined: June 2nd, 2001, 2:01 am
- Location: Kennesaw, Ga, USA
- Contact:
Re: What engine do I have?
Damnit Barry!
Okay so it came in one Ford that no one has ever heard of.
LOL
![Freak :freak:](./images/smilies/freak.gif)
Okay so it came in one Ford that no one has ever heard of.
LOL
![Freak :freak:](./images/smilies/freak.gif)
Re: What engine do I have?
I only paid $150.00. We are in the process of changing the IM. One response said this may be a KFZE, how can I tell? Having to change the flywheel made me think that this may not be a KLDE.
- Custommx3
- Site Administrator
- Posts: 8391
- Joined: November 7th, 2000, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Lat 35.1N Lon -90W
- Contact:
Re: What engine do I have?
if u have a K8 on the block and k8 on the heads, u have a k8. KFs have KF on the block and k8 heads, KLDEs/ZEs have KL on the block and KL on the heads.
you have a K8 im almost sure of it, take a pic of the engine if you can, but I wanna know whats on the cams.
<small>[ July 29, 2004, 03:39 PM: Message edited by: Custommx3 ]</small>
you have a K8 im almost sure of it, take a pic of the engine if you can, but I wanna know whats on the cams.
<small>[ July 29, 2004, 03:39 PM: Message edited by: Custommx3 ]</small>
Re: What engine do I have?
According to my Mazda Parts Catalogue, its somewhat confusing with the heads numbering, as K8 and KF are used interchangeably. K8 and KF engines up to 970118 have K8 right cylinder head and KF left , after 970118 its KF on right and left. The only way to tell one from the other is to look at the block.
<small>[ July 29, 2004, 03:57 PM: Message edited by: IanL ]</small>
<small>[ July 29, 2004, 03:57 PM: Message edited by: IanL ]</small>
Re-shaped and re-sized gearshift lever. Best driveability mod you can do!
Extra thick soundproofing in the boot (trunk) to quieten my stainless steel exhaust system![Smile :)](./images/smilies/icon_smile.gif)
Extra thick soundproofing in the boot (trunk) to quieten my stainless steel exhaust system
![Smile :)](./images/smilies/icon_smile.gif)
- Custommx3
- Site Administrator
- Posts: 8391
- Joined: November 7th, 2000, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Lat 35.1N Lon -90W
- Contact:
Re: What engine do I have?
The serial number on the engine is K8 289020
![Smile :)](./images/smilies/icon_smile.gif)
- Zoso124
- Forum Moderator
- Posts: 1100
- Joined: November 7th, 2000, 2:01 am
- antispam: No
- Location: Sterling, VA
Re: What engine do I have?
I'm with Native American, I'll bet the bank its a 1.8L, hell I used the KL Intake and Ford Valve cover on my 1.8L for years.
Mike Evans
Gone:
92 GS Tropical Emerald MTX 2.5L
93 GS Raspberry Metallic SE MTX 1.8L
Gone:
92 GS Tropical Emerald MTX 2.5L
93 GS Raspberry Metallic SE MTX 1.8L