neone installed pacesetter headers on klze with success?
-
- Regular Member
- Posts: 64
- Joined: June 13th, 2003, 2:01 am
- Location: Atlanta/Toronto
neone installed pacesetter headers on klze with success?
I am in the market for headers for my klze and I heard that pacesetter would be best suited for the klze. The prob is fitment with these headers. Neone successfully installed these properly and what gains can i expect?<p>Thx in advanced
"They're 2 types of people in this world, people that work for money and people that make money work for them."
- Zoso124
- Forum Moderator
- Posts: 1100
- Joined: November 7th, 2000, 2:01 am
- antispam: No
- Location: Sterling, VA
Re: neone installed pacesetter headers on klze with success?
2hp
Mike Evans
Gone:
92 GS Tropical Emerald MTX 2.5L
93 GS Raspberry Metallic SE MTX 1.8L
Gone:
92 GS Tropical Emerald MTX 2.5L
93 GS Raspberry Metallic SE MTX 1.8L
-
- Regular Member
- Posts: 64
- Joined: June 13th, 2003, 2:01 am
- Location: Atlanta/Toronto
Re: neone installed pacesetter headers on klze with success?
<blockquote><font size="1" face="Verdana, Arial">quote:</font><hr>Originally posted by Zoso124:
2hp<hr></blockquote><p>a measly 2hp! I was thinkin at least 7-10 whp!
If that is the case then I wont even bother with them.<p>neone else?
2hp<hr></blockquote><p>a measly 2hp! I was thinkin at least 7-10 whp!
If that is the case then I wont even bother with them.<p>neone else?
"They're 2 types of people in this world, people that work for money and people that make money work for them."
-
- Senior Member
- Posts: 3391
- Joined: November 30th, 2001, 2:01 am
- Location: Stuttgart, Deutschland
- Contact:
Re: neone installed pacesetter headers on klze with success?
they are'nt a direct fit but they will bolt up to the heads but you will have to push the cat back a few inches.<p>But i know a guy with a KLZE in a 626, and he says the difference in power is like night and day. Not sure what that means, but he says it made a big difference.
<p>I plan on buying these headers for my KLZE after I pass emissions and get the full exhaust redone. I'm going to wrap them in some exhaust wrap, hopefully that will prevent them from rusting.
![Shrug :shrug:](./images/smilies/shrug.gif)
Noble Green Metallic 93' GS Hybrid, 91' 1.8 323
DONATE TO MX-3.COM
DONATE TO MX-3.COM
-
- Regular Member
- Posts: 1079
- Joined: February 13th, 2001, 2:01 am
- Location: Hartford, CT
- Contact:
Re: neone installed pacesetter headers on klze with success?
7-10 whp for headers? lol....<p>modding a car isn't plug and play guys...
- Buff1110
- Supporting Member
- Posts: 588
- Joined: February 26th, 2001, 2:01 am
- Location: Howell, NJ, USA
Re: neone installed pacesetter headers on klze with success?
no they do not fit easily, by the time mine finally fit on the ze i couldnt get a good seal on the y pipe to headeres. the front flange hits the oil pan and the rear header flange hits the frame so u cut those off then u cant get a decent seal. save ur money for a 65mm tb or something else
Dan
92 Mx-3 Gs, KLZE Powered!! - SOLD!!!!
02 Tacoma TRD - Daily
93 Honda del Sol - New Project
92 Mx-3 Gs, KLZE Powered!! - SOLD!!!!
02 Tacoma TRD - Daily
93 Honda del Sol - New Project
Re: neone installed pacesetter headers on klze with success?
I am not sure about power differences cause when I installed my HOTSHOT headers, I did everything at once when installing the KLZE motor.. However it installs rather easy. It all bolts right up, with just a few mods to it .. Do a search on this there is plenty of info out there already on this subject... :p
Re: neone installed pacesetter headers on klze with success?
7-10bhp is about right not wheel hp though. Pacesetters fit like crap but they are redesigning them right now. They do make the most HP though.....
93 Mx-3 GS klze swapped(sold)
96 Integra LS DD
91 Crx Si drag car
2.0L sleeved gsr block, forged internals, skunk2 valvetrain, HP racing intake manifold, Holset H1 turbo, 1000cc injectors, short geared lsd transmission, 3" turboback exhaust. 20 psi![Smile :)](./images/smilies/icon_smile.gif)
96 Integra LS DD
91 Crx Si drag car
2.0L sleeved gsr block, forged internals, skunk2 valvetrain, HP racing intake manifold, Holset H1 turbo, 1000cc injectors, short geared lsd transmission, 3" turboback exhaust. 20 psi
![Smile :)](./images/smilies/icon_smile.gif)
-
- Regular Member
- Posts: 64
- Joined: June 13th, 2003, 2:01 am
- Location: Atlanta/Toronto
Re: neone installed pacesetter headers on klze with success?
the pacesetters are 2 1/4 piping correct? The hotshots are 2 1/2 and bosal is ?. I think that with hotshots you will loose torque and gain some high end power which would be better for nos or supercharged engines. I guess you can cut and weld the ps headers to the y pipe for maximum fitment but it would be nice to see some dyno graphs and pics of install.
"They're 2 types of people in this world, people that work for money and people that make money work for them."