Hey all,
I was wondering about what kind of fog lights I can put in my MP5 bumper? I know they are 5" holes but most if not all the fog lights I'm seen seem to attach via a bracket and not flush like would make sense to me. So, I'm wondering what other people have used. Thanks.
Steve
Search found 231 matches
- September 14th, 2004, 4:39 pm
- Forum: Appearance
- Topic: mp5 Fog Lights?
- Replies: 2
- Views: 233
- August 3rd, 2004, 10:10 pm
- Forum: Appearance
- Topic: warning Onderground MP5 bumper
- Replies: 16
- Views: 253
Re: warning Onderground MP5 bumper
Ok dokey. Pictures are posted on my cardomain site. A link should be in my address line.
Steve
Steve
- July 28th, 2004, 7:05 pm
- Forum: Appearance
- Topic: warning Onderground MP5 bumper
- Replies: 16
- Views: 253
Re: warning Onderground MP5 bumper
Well, I chopped a couple inches off of each side making it pretty much straight across the entire bottom. This removed most of the damage fiberglass as well as raising it up. Honestly, I think it actually has more ground clearance than the stock bumper with the GS lip on. However, it sits out furthe...
- July 20th, 2004, 12:01 pm
- Forum: Appearance
- Topic: warning Onderground MP5 bumper
- Replies: 16
- Views: 253
Re: warning Onderground MP5 bumper
I just checked and I have 1 leatherman's length of clearance...4 inches. Comparing it to the curb that it is in front of it, I am an inch or 2 lower than the stock bumper with GS lip was running. The stock bumper and lip would scrap on the bottom if I got too close to the curb but this is now well b...
- July 20th, 2004, 11:17 am
- Forum: Appearance
- Topic: warning Onderground MP5 bumper
- Replies: 16
- Views: 253
warning Onderground MP5 bumper
Hey all, I just wanted to give you a heads up on this bumper. I just had one installed last week and while quality and fit/finish are fine, it just sits too bloody low. I have H&R sport springs on my car with the stock tires so I sit a little lower but not much and this bumper scrapes on everyth...
- July 20th, 2004, 11:06 am
- Forum: Appearance
- Topic: corksport hatch shade
- Replies: 3
- Views: 148
Re: corksport hatch shade
I have one of the Corksport hatch shades. I'll try and post pictures to my cardomain site tonight. Two things to be aware of. First, the metal clips they give you to hold it on rust pretty quickly. I would paint them before putting them on the car. And second, contrary to what they tell you about th...
- May 12th, 2004, 4:29 pm
- Forum: Appearance
- Topic: Slim Visors are back :)
- Replies: 56
- Views: 5660
Re: Slim Visors are back :)
The ones in the picture are the newer ones. I have a set on my car (see cardomain page).
Steve
Steve
- May 3rd, 2004, 3:08 pm
- Forum: Appearance
- Topic: side window wind deflectors
- Replies: 1
- Views: 102
- April 1st, 2004, 6:47 pm
- Forum: Appearance
- Topic: Ebrake handle
- Replies: 8
- Views: 200
Re: Ebrake handle
I have one too. There's a pic on my cardomain page.
Steve
Steve
- March 25th, 2004, 1:08 pm
- Forum: General Mazda MX-3
- Topic: anyone live in wis..and whats the legal limit for tint
- Replies: 4
- Views: 98
Re: anyone live in wis..and whats the legal limit for tint
If they are like Oregon, the DOT will have a web site and a downloadable copy of the driver's manual. That should tell you what the tint limit is.
Steve
Steve
- March 25th, 2004, 1:03 pm
- Forum: V6 Technical/Performance
- Topic: Throttle Bodies??
- Replies: 5
- Views: 62
Re: Throttle Bodies??
Ok, but what about other factors like drivability and gas mileage?
Steve
Steve
- March 4th, 2004, 2:50 pm
- Forum: V6 Technical/Performance
- Topic: check engine light with PRM intake
- Replies: 4
- Views: 54
Re: check engine light with PRM intake
Well, I have the code reset according to the instructions. I've also had some stereo work done since then (an amp as well as a powered sub...both done at different times) so I believe the battery has been disconnected for more than 30 seconds. Is there something else that has to be done to reset the...
- March 4th, 2004, 1:34 pm
- Forum: V6 Technical/Performance
- Topic: check engine light with PRM intake
- Replies: 4
- Views: 54
check engine light with PRM intake
My check engine light has been coming on and when I had it hooked up to the computer it said the cause was too warm of air coming into the intake. I have a PRM intake with the metal tube directed into the fender area. The thing that baffles me is that the light comes on not only after the car is war...
- January 27th, 2004, 6:20 pm
- Forum: Appearance
- Topic: Anyone intrested in new Mx-3 Headlights?
- Replies: 43
- Views: 730
Re: Anyone intrested in new Mx-3 Headlights?
What are morrette lights? Is there a picture somewhere?
Steve
Steve
- January 26th, 2004, 6:24 pm
- Forum: V6 Technical/Performance
- Topic: pulleys
- Replies: 7
- Views: 41
Re: pulleys
I have one and I like it. It allows your engine to rev quicker since it has less weight bogging it down. Be aware though that you will need to do some cutting to the shroud to make it fit. Also, you are going to need a different sized belt than what you have currently.
Steve
Steve