[FS] Partout 1993 AWD MX-3

RobMinhas · Post by **RobMinhas** » June 9th, 2014, 1:37 pm

Any interest in selling the intake manifold by itself Tim?

MrMazda92 · Post by **MrMazda92** » June 10th, 2014, 9:33 pm

It's really far out for me, but worth a shot... Any chance you'd part with just the rear end, from the subframe to the hubs(brakes and all)?

I would have to figure out a shipping method, obviously, but I am interested. Also, do you have a fueltank that saddles over the subframe, or did you go with a fuel cell?

projectmx · Post by **projectmx** » June 18th, 2014, 4:11 pm

I have another person interested in the engine, if they don't want the intake I would sell it

The brakes are gone so no go there and if I sell the rear subframe I will have no way to get the car to the recycling place which is where the shell and sadly rear gtr subframe and custom front mx3 subframe will all go, I may see if I can pull the custom steering rack though

and I do not have the saddle tank I did a fuel cell

MrMazda92 · Post by **MrMazda92** » June 19th, 2014, 12:10 am

Well, I would be willing to ship up my extra rear subframe, if that helps at all... Or, is there any chance I could convince you to remove it AT the recycling place?

I give you my word that it would go to a very worthy cause... A streetable RWD project that I'm planning to piece together bit by bit.

What all custom work did you do to the front subframe, if you don't mind me asking?

I can live without the tank, but I would consider it a terrible loss for that subframe to go to waste in a recycling center

projectmx · Post by **projectmx** » June 23rd, 2014, 6:50 am

only another AWD subframe will fit the car now, I had custom frame rails built on the mx3 to allow me to install the AWD rear subframe and the front one is heavily modified to fit an AWD trans. I will see if they will let me remove it once its there but I am not sure how that will go over.

projectmx · Post by **projectmx** » June 23rd, 2014, 6:52 am

the front subframe I had to cut out enough of the frame to fit the AWD trans then had to cut out pieces of metal to weld back into the subframe then sand blasted it and coated it with POR-15

Mr_Shorty · Post by **Mr_Shorty** » June 28th, 2014, 11:40 pm

Interested in the tranny. Shipped price to V2G 1P4. Thanks.

MrMazda92 · Post by **MrMazda92** » June 29th, 2014, 2:08 am

I definitely appreciate you making the effort to do this for me, man!

I do have a few contacts in Canada, so maybe I could arrange for a friend to drive it down for me... That might make it doable!

projectmx · Post by **projectmx** » July 3rd, 2014, 7:33 am

I found out I will be able to pull the subframes at the junk yard so knuckles and subframes will be available subframes will be $200 each the set of knuckles with brand new hubs installed will be $80 for the set and the custom steering rack will be $100

Mr_Shorty · Post by **Mr_Shorty** » July 3rd, 2014, 9:40 am

Tranny?? Priced shipped? Thanks.

projectmx · Post by **projectmx** » July 4th, 2014, 6:37 am

Mr shorty I just rechecked and my first post does indicate the entire drive system is gone

MX-3.com

[FS] Partout 1993 AWD MX-3

Re: [FS] Partout 1993 AWD MX-3

Re: [FS] Partout 1993 AWD MX-3

Re: [FS] Partout 1993 AWD MX-3

Re: [FS] Partout 1993 AWD MX-3

Re: [FS] Partout 1993 AWD MX-3

Re: [FS] Partout 1993 AWD MX-3

Re: [FS] Partout 1993 AWD MX-3

Re: [FS] Partout 1993 AWD MX-3

Re: [FS] Partout 1993 AWD MX-3

Re: [FS] Partout 1993 AWD MX-3

Re: [FS] Partout 1993 AWD MX-3