[FS] Partout 1993 AWD MX-3

[projectmx]

Due to having a baby, now moving and simply not having time to work on a car I am to parting my nearly completed AWD mx-3


In most cases people will have to pull the part off the car themselves. Prices are listed with parts I will take Canadian or united states currency.

loose items I may have time to ship especially if you are buying a large group of items. I simply do not have time to make a hundred trips to the post office, It is hard enough to find time to make a handful in a month.

http://www.cardomain.com/ride/2241376/1993-mazda-mx-3 here is a link to my not super up to date cardomain site

Body: ($700 includes suspension front and rear AWD subframes)
In very good shape no rust that I can find
Extra set of doors that are shaved and have door poppers in them ($300)
Extra set of front fenders ($80)
Needs the front bumper cover
Including Buddy Club 2 side skirts and rear bumper ($150)
Rare RS spoiler ($200)
Extra hood, carbon fiber ($150)Hood is gone

Engine:
BP engine with: ($600 does not include anything with a price listed bellow) Engine has offer
ported/polished/port matched head
bpt323's special modified intake manifold
exintake mod done
OBX adjustable cam gears
1mm oversized flat top valves
overbored wiseco 10.2:1 pistons
ARP head studs
4-2-1 header (I think its pacesetter but can't recall) ($100)
engine was balanced
also has a slightly upgraded oil pump from GTR engine (brand new)
AEM EMS computer to control the engine ($400) EMS no longer selling
CAS from miata and coil packs to match
custom engine wire harness built by Bpt323 (harness is even designed to add Coil On Plug later if
you want) ($100) Harness has offer
vishnu fuel rail ($100) No longer for sale
Newly professionally cleaned injectors
oil filter relocation kit ($100) No longer for sale
b6t rods
NGK wires ($30) Wires have offer
Nisan Silvia much larger aluminum radiator custom fitted ($150) radiator sold
slim fan for radiator ($50) Fan sold


trans: ($800 for trans/GTR drive shaft/front and rear diff/ axles) Drivetrain sold
cernterforce spec 2 dual friction clutch ($80) Clutch has offer
fidanza lightweight flywheel ($200) Flywheel has offer
entire GTR AWD system from front to back.
2 custom built engine/trans mounts to allow the AWD setup to fit into the car.
custom built spacer to allow drive shaft to fit car
custom built mount for carrier baring

brakes: Brake setup has sold
Front stock GS brakes ($50)
rear 2004 mazdaspeed miata sport breaks ($100)
stainless steel braided brake lines ($60)

Other:
Custom modified from subframe to house gtr trans
Custom built engine support member
Rear frame rails custom built to bolt up the GTR AWD rear subframe
Spare tire well removed and partial enclosure built for fuel cell
Fuel cell included ($60)
Inline fuel pump and inline fuel filter ($100)
SS braided hoses for fuel lines in rear ($100)
Includes a 93 dash frame, and 94 dash frame with dash that can be reassembled if you want
Also front two very hard to find Axles are brand new
Japanese spec GTR rear axles

Also have a 1994 Miata ECU and engine harness for sale for $250


The drive shaft is now also completely installed with a custom spacer between the drive shaft and front diff to make up for the fact the mx-3 is a little longer, and has a custom bracket built for the center carrier bearing (those two items alone cost me just over a grand)

There are also a few aftermarket gauges, a pillar gauge holder ($50), slim visors ($100), aftermarket seats ($200), and a carputer with 7" touchscreen ($200) I will include. I have put nearly $10,000 into this car so my asking prices is very fair.

[Savin]

Damn I so wish I could buy this so I can finally see it finished after all these years.

Good luck with the sale and I hope someone buys the whole thing and finishes it and doesn't part it out!

[projectmx]

changed price

[Josh]

Man I wish this was not in Canada...

[RobMinhas]

Man I wish this was not in Canada...

I wish it was in my side of Canada. I'd at least try to get that engine from him.

[projectmx]

This may be a Canadian car now but I still have my papers from America

also slightly lowered price and included a few parts I had forgot about

[projectmx]

I also had an offer today on the engine/ aem ems / wire harness I may accept

[projectmx]

it is looking like the car will be parted out, so far I have offers on the engine, engine wire harness, aem ems, calipers, rotors, chasis, and two offers on the drivetrain

[Savin]

[RobMinhas]

I fired you a PM on clubprotege.com about the radiator setup.

[projectmx]

believe me guys after spending close to 10 years trying to put this car together I don't want to part it. I've asked for help trying to get this put together even offered a few grand to anyone willing to come help me get it running but no one took me up on the offer. if the car sits any longer it won't be any good. I may as well sell so all this great work goes somewhere at least. hopefully I can buy a running mx-3 or mx-5 sometime in the near future once I have sold off the car and saved some money so I can still be part of the mazda community again.

[Savin]

I just wish the car was still down in Morocco, IN. I sure as f--- would be there every freakin' weekend helping you finish it!

[projectmx]

Everything is updated now with what is for sale, I likely have some other items I am not remembering so as the garage gets cleared out I may add more items

also I should have any needed tools to remove parts when you arrive.

[projectmx]

updated with what's sold

[projectmx]

new updates with items sold, and no longer being sold.

also engine is out of car so whoever buys it doesn't need to pull it

items listed as offer are still for sale, until I see money these items are up for grabs