225/50 on an 8J will look like this, looks massive to me lol
I thought 16x8 grids where only available in ET10 or 20? If so I would go 20 and hope you don't throw mexipoke
Wheels...
-
- Regular Member
- Posts: 855
- Joined: October 8th, 2009, 12:36 pm
- antispam: No
- Location: United Kingdom
Re: Wheels...
Last edited by youdirtyfox on April 13th, 2013, 12:30 pm, edited 1 time in total.
- Ryan
- Senior Member
- Posts: 7198
- Joined: April 7th, 2008, 1:06 pm
- antispam: ~SPAM*SUX~
- Location: Manitoba
Re: Wheels...
available in +20. So you're saying they'll fit?
I was going to go do some measurements later...
I was going to go do some measurements later...
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
-
- Regular Member
- Posts: 855
- Joined: October 8th, 2009, 12:36 pm
- antispam: No
- Location: United Kingdom
Re: Wheels...
Yea I would measure as I think you will have tread outside the arch.
Low offset wide rims need at least some stretch...
Low offset wide rims need at least some stretch...
- MazdaMan1991
- Regular Member
- Posts: 270
- Joined: January 18th, 2013, 12:01 pm
- antispam: ~SPAM*SUX~
- Location: Florida
- Contact:
Re: Wheels...
Perty
My Mazdas
2008 Mazda 3 FS auto - Totaled
1994 Mazda 626 KL 5 spd - sold
2002 Mazda Millenia S - sold
1994 Mazda MX-3 RS 5 spd - bp swapped
My Worklog/Build Thread
My YouTube Page
2008 Mazda 3 FS auto - Totaled
1994 Mazda 626 KL 5 spd - sold
2002 Mazda Millenia S - sold
1994 Mazda MX-3 RS 5 spd - bp swapped
My Worklog/Build Thread
My YouTube Page
- Ryan
- Senior Member
- Posts: 7198
- Joined: April 7th, 2008, 1:06 pm
- antispam: ~SPAM*SUX~
- Location: Manitoba
Re: Wheels...
Did the math, I need 1/2" more height clearance in the wheel well from stock
And 0.79" (20mm) total width clearance. This doesn't seem like a lot, so I'm thinking it should fit.
Just need to measure where stock wheel exists in the well, and determine what offset to get.
I have access to a fender roller and I'm not afraid to take a sledge to the spring mount.
Too bad it snowed today.
Also speedo should read 4% slow. (100 on the clock is 104 on the gun)
And 0.79" (20mm) total width clearance. This doesn't seem like a lot, so I'm thinking it should fit.
Just need to measure where stock wheel exists in the well, and determine what offset to get.
I have access to a fender roller and I'm not afraid to take a sledge to the spring mount.
Too bad it snowed today.
Also speedo should read 4% slow. (100 on the clock is 104 on the gun)
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback