[FS] AWD MX-3

[projectmx]

Due to having a baby and simply not having time to work on a car I am to selling my nearly completed AWD mx-3 for $2500 or trading for a driving mx3 or miata in good shape (I will also consider trade and adding some money).
http://www.cardomain.com/ride/2241376/1993-mazda-mx-3 here is a link to my not super up to date cardomain site

Body:
in very good shape no rust that I can find and i have an extra set of doors that are shaved and have door popers in them and an extra set of front fenders just in case
just missin the front bumper
including bc2 side skirts and BC2 rear bumper
Rare RS spoiler

engine:
BP engine with: ported/polished/port matched head, bpt323's special modified intake manifold, exintake mod done, adjustable cam gears, 1mm oversized flat top valves, overbored wiseco 10.2:1 pistons (may be 10.5:1 when you include the valves which will be amazing with turbo later), ARP head studs, engine was balanced, also has a slightly upgraded oil pump from GTR engine (brand new), AEM EMS computer to control the engine, CAS from miata and coil packs to match, custom engine wire harness built by Bpt323 (harness is even designed to add Coil On Plug later if you want), vishnu fuel rail, oil filter relocation kit and lastly b6t rods

trans:
spec 2 dual friction clutch can't recall the company but it was a good one, fidanza lightweight flywheel, entire GTR AWD system from front to back.
2 custom built engine/trans mounts to allow the AWD setup to fit into the car.
custom built spacer to allow drive shaft to fit car
custom built mount for carrier baring

brakes:
Front stock GS brakes, rear 2004 mazdaspeed miata sport breaks, stainless steel braided brake lines

Other:
Custom modified from subframe to house gtr trans, custom built engine support member, rear frame rails custom built to bolt up the GTR AWD rear subframe, sparetire well removed and partial enclosure built for fuel cell, fuel sell included, inline fuel pump and inline fuel filter, SS braided hoses for fuel lines in rear, includes a 93 dash frame, and 94 dash frame with dash that can be reassembled if you want. Also front two very hard to find Axles are brand new and rears are what came with the car but look in good shape.

The drive shaft is now also completely installed with a custom spacer between the drive shaft and front diff to make up for the fact the mx-3 is a little longer, and has a custom bracket built for the center carrier bearing (those two items alone cost me just over a grand)

There are also a few aftermarket gauges, a pillar gauge holder, slim visors, aftermarket seats, and a carputer with 7" touchscreen I will include. I have put nearly $10,000 into this car so my asking prices is very fair.

[mikeinaus]

why are you selling? you look so close to being finished...

[projectmx]

the place i'm storing it fell through and i as of now have no where to put it, and no help to complete the car cause i'm at a point where i don't know how to do some of the items left so unless a new place to store the car comes through i have to sell it

[Daninski]

Stupid question but I assume the car will need to be trailered away?

[wytbishop]

This is a project that I've always wanted to do myself. I think your asking price is reasonable but I worry that you'll have trouble finding someone who has the money and wants a project this big. If I was closer who knows. I wish you luck.

[projectmx]

Yeah it will have to be trailored

[projectmx]

bump with updates! i updated a few items in the first post and forgot to mention I have some new brake lines installed and brakes are hooked up now. I want to keep the car but i just don't have anywhere to put it while I work on finishing it. if i could get the car to the point where it at least drives i'd be keeping it but i don't have the garage space

[Savin]

Since it seems to just be electrical stuff that is left, why not just use a stock BP harness for the time being. Wouldn't that at least make it run so you could drive it?

I wish you could store the car back down in Morocco, I'd be more than glad to try and attempt to help you finish it.

[projectmx]

a stock bp harness will not work on this car it has a CAS and coil pack, the custom engine wire harness is also set up to run coil on plug if you want plus it has an AEM EMS instead of the stock ECU just the ECU alone is worth over a grand, plus the car computer and touch screen thats another $500 the car is a steal

[Josh]

This is like a roller coaster of disappointment

If I had the cash right now I would!

[projectmx]

its been rough getting married and moving to another country.. i really wish i had held out for a place with a 2 car garage but i caved and my wife doesn't really want to give up putting her car in the garage and i can't leave the mx-3 out on the side of the road i'm sure it would get towed

[projectmx]

I just made some changes to the initial post to update what has been done to the car and what is included. More is included and the price is down from what it was before. It is also officially for sale.

[Savin]

.....If I could, I would buy it, But I can't. I've wanted to see this car finished since you first started working on it back in '07.

[projectmx]

believe me i wanted to see it done also.

[Josh]

Hope you are doing well buddy it has been a while!