[WTB] Millenia intake & more
-
- Regular Member
- Posts: 162
- Joined: August 31st, 2008, 12:40 pm
- Location: Burlington, Ontario
- Contact:
[WTB] Millenia intake & more
Hello everyone,
i have been doing some research the last couple of days... and I have come across a couple of decisions I have made, for upgrading my engine.
First off I am looking to buy a Millenia IM with the throttle body / terminal block and hopefully the Virs solenoids and IAC..
if anyone has been to a junkyard recently and knows where let me know please..
2. New oil pump (dealer only??)
3. Head gaskets (felpro MLS) any good???
4. filled engine mounts (custom right?)
5. Probinator chip.. for my mx6 ECU
6. slotted / drilled rotors & pads (whats a good brand?)
My thoughts on the next 2 I am thinking about... Not right now but maybe in a few years (need to follow up on and read) I am thinking of turbo'ing my mx3, having that in mind since my engine will be apart in the next couple of weeks. I am looking at the 10.1-1 wiseco Pistons 85mm with forged rods not sure on the band though still looking.
The last would be to get a 255 walbro fuel pump high pressure? or low pressure? even if I am not turbo'ing would 255 walbo be a good choice ?
i have been doing some research the last couple of days... and I have come across a couple of decisions I have made, for upgrading my engine.
First off I am looking to buy a Millenia IM with the throttle body / terminal block and hopefully the Virs solenoids and IAC..
if anyone has been to a junkyard recently and knows where let me know please..
2. New oil pump (dealer only??)
3. Head gaskets (felpro MLS) any good???
4. filled engine mounts (custom right?)
5. Probinator chip.. for my mx6 ECU
6. slotted / drilled rotors & pads (whats a good brand?)
My thoughts on the next 2 I am thinking about... Not right now but maybe in a few years (need to follow up on and read) I am thinking of turbo'ing my mx3, having that in mind since my engine will be apart in the next couple of weeks. I am looking at the 10.1-1 wiseco Pistons 85mm with forged rods not sure on the band though still looking.
The last would be to get a 255 walbro fuel pump high pressure? or low pressure? even if I am not turbo'ing would 255 walbo be a good choice ?
- Ryan
- Senior Member
- Posts: 7198
- Joined: April 7th, 2008, 1:06 pm
- antispam: ~SPAM*SUX~
- Location: Manitoba
Re: [WTB] Millenia intake & more
I'm sure you can get Ebay oil pumps. Unless you want to bend over at Mazda.
Even though, do you have a ZE? Not sure how parts are for that on this side of the pond.
Gaskets, the general consensus I've gathered is anything is good. Ebay again. Except maybe rubbers.
Yes, custom filled mounts, unless you want to pay with body parts (~150?)
Solo_Ryder has pads or rotors for sale, unless he sold them already.
Even though, do you have a ZE? Not sure how parts are for that on this side of the pond.
Gaskets, the general consensus I've gathered is anything is good. Ebay again. Except maybe rubbers.
Yes, custom filled mounts, unless you want to pay with body parts (~150?)
Solo_Ryder has pads or rotors for sale, unless he sold them already.
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
Re: [WTB] Millenia intake & more
I wouldn't suggest drilled rotors...
I would suggest some brembo slotted rotors. I have brembo slotted with akebono ceramics and I am very happy with them.
I would suggest some brembo slotted rotors. I have brembo slotted with akebono ceramics and I am very happy with them.
-
- Regular Member
- Posts: 162
- Joined: August 31st, 2008, 12:40 pm
- Location: Burlington, Ontario
- Contact:
Re: [WTB] Millenia intake & more
I have the 93 Probe GT engine. ssooooo KLDE.. almost positive..
-
- Regular Member
- Posts: 46
- Joined: February 2nd, 2009, 12:09 am
- Location: Grande Prairie, Alberta
Re: [WTB] Millenia intake & more
I have an intake manifold.
Either PM me...
or check out probetalk, mx6 or mx-6 (.ca) too see pics
Either PM me...
or check out probetalk, mx6 or mx-6 (.ca) too see pics
-
- Regular Member
- Posts: 162
- Joined: August 31st, 2008, 12:40 pm
- Location: Burlington, Ontario
- Contact:
Re: [WTB] Millenia intake & more
PM sent, where do you live??
-
- Regular Member
- Posts: 46
- Joined: February 2nd, 2009, 12:09 am
- Location: Grande Prairie, Alberta
Re: [WTB] Millenia intake & more
replied..
And Grande Prairie Alberta.
And Grande Prairie Alberta.
-
- Regular Member
- Posts: 162
- Joined: August 31st, 2008, 12:40 pm
- Location: Burlington, Ontario
- Contact:
Re: [WTB] Millenia intake & more
how much would it cost to ship it to burlington ON, L7s2c5
-
- Regular Member
- Posts: 46
- Joined: February 2nd, 2009, 12:09 am
- Location: Grande Prairie, Alberta
Re: [WTB] Millenia intake & more
Pretty close to 30cdn for regular post. (6 days)
- escortluver19
- Regular Member
- Posts: 130
- Joined: April 9th, 2006, 11:19 pm
- Location: waukesha, wisconsin
- Contact:
Re: [WTB] Millenia intake & more
are you going to be using milennia S rods? If so i have a set in great condition that i wont be using anymore.Ive also got milennia S injectors still in rails too if your interested.PM me if youd like, i have limited internet access but i have email on my phone.
93 escort lx-sold
90 mx6 gt-sold
93 probe gt-sold
93 escort wagon-sold
93 escort gt-v6 and loving it FOR SALE
90 mx6 gt-sold
93 probe gt-sold
93 escort wagon-sold
93 escort gt-v6 and loving it FOR SALE
-
- Regular Member
- Posts: 1083
- Joined: August 23rd, 2008, 12:09 am
- Location: Beamsville.
Re: [WTB] Millenia intake & more
why do you want a millenia intake manifold? if it is a 93 klde then the intake mani that comes stock on that will work with no mods. plus the intake ports are rectangular with ze IM and the stock de heads are rounded so they wouldnt match up correctly
NEED PARTS INSTALLED? PM ME!
![Image](http://i453.photobucket.com/albums/qq253/projectzemx3/avator2.jpg)
![Image](http://i453.photobucket.com/albums/qq253/projectzemx3/avator2.jpg)
- Nd4SpdSe
- Senior Member
- Posts: 11212
- Joined: May 25th, 2002, 2:01 am
- Location: Québec City, Quebec, Canada
- Contact:
Re: [WTB] Millenia intake & more
Apparently despite that many say there is a gain of 5-10hp just swapping the IMsprojectzemx3 wrote:why do you want a millenia intake manifold? if it is a 93 klde then the intake mani that comes stock on that will work with no mods. plus the intake ports are rectangular with ze IM and the stock de heads are rounded so they wouldnt match up correctly
1992 Mazda Mx-3 GSR - 2.5L KLZE : Award Winning Show Car & Race Car ['02-'09] (Retired)
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
-
- Regular Member
- Posts: 162
- Joined: August 31st, 2008, 12:40 pm
- Location: Burlington, Ontario
- Contact:
Re: [WTB] Millenia intake & more
I currently have 2 klde motors... after some serious reading.. I am thinking of just buying a klZE motor, rebuild it (bottom end with new rods and bearings) and put on KLZE heads after doing a 3deg. angle job with KLDE retainers and springs.. with a curved neck ZE IM ???
does that sound right?
how muchdo you think I might be spending ??
and sell my 1.5 klde motors for parts lol
does that sound right?
how muchdo you think I might be spending ??
and sell my 1.5 klde motors for parts lol