![Crying or Very sad :cry:](./images/smilies/icon_cry.gif)
[WTB] 92-93 Guage Cluster
[WTB] 92-93 Guage Cluster
As it says i need a 92-93 Guage Cluster. I was putting in glow gauges in mine and had my fuel needle brake off
I put just i little to much pressure on it
![Crying or Very sad :cry:](./images/smilies/icon_cry.gif)
1992 WHITE 1.6l SOHC saving for a BPT swap next year, New interior next month, and new Paint Hooray
- PATDIESEL
- Senior Member
- Posts: 4476
- Joined: August 13th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Atlanta, GA.
I have some. I sell them for 94+ RSs or any year GS in miles not KM only. The go for 75 bucks and I have a range of milages.
Most under 100K miles.
EMAIL me if interested.
Do not PM me I cannot keep track of PM parts requests.
Thanks, Patrick
Most under 100K miles.
EMAIL me if interested.
Do not PM me I cannot keep track of PM parts requests.
Thanks, Patrick
![Image](http://www.patdiesel.atlantamx3.com/MX-3/patdieselsigMX-3.jpg)
ZE -strait neck,headers,2.5 exhaust,pheno spacers,lower cross member,GC coils,MS struts,Brembo slotted rotors,filled MS mounts,SS brake/clutch lines, CAI,to rear bat reloc,Hella headlamps,Hella DE fogs 180WHP
- Limegreen mx-3
- Regular Member
- Posts: 1778
- Joined: October 29th, 2002, 2:01 am
- Location: San Antonio TX
- Contact:
hit up a local junkyard unsrew the fuel guage from a 92-96 guage cluster install ur gueges and them install ur fuel guage last thats what i did when i didn't know any better. that way it doens't breck on u again. better than paying extra money for one part that u can get cheap at a junkyard.
(12.4@118@18psi) 92 MX-3, KIA (BP-DE)Swap, Electromotive TEC II Standalone, 8,200 Rev Limit, Custom Intake/Exhaust Manifold, 1,000cc PTE Injectors, Custom Fuel Rail, Aeromotive FPR, 80MM Holley TB, MSD 8.5MM Wires, NGK V-Power #8, SC6262 Turbo, 3 in. DownPipe, Tial WG/BOV, 600HP PTE FMIC, 2.5IN Intercooler Piping, EQUUS/Autometer KIA G-Series Tran, Extreme ACT Clutch, Built BP in starting process.
- slimmyslim1420
- Regular Member
- Posts: 381
- Joined: October 22nd, 2005, 12:22 pm
- Location: Tennessee
I had the same problem when I put on my glow gauges. I simply replaced the needle with a piece of a toothpick. Of course I painted all of my needles so you can't even tell it.
1992 GS ZE swap 94 dash swap drilled and slotted rotors full ceramic pads CS SS clutch and brake lines KL-36 ecu zx-2 tokico struts eibach springs short shifter Tenzo exhaust Hi flow cat 2.5 in piping
Well the needle broke off at the pin that comes out of the gauge so i dont think i can replace the needle. But let me know if you have a guage cluster. jimishadow said he had one for me for like 30 bucs shipped if that doesnt go through ill still need one. Thanks guys.
1992 WHITE 1.6l SOHC saving for a BPT swap next year, New interior next month, and new Paint Hooray