Need part name.

93_mx3_gs · Post by **93_mx3_gs** » November 6th, 2005, 5:20 pm

Alright, I need the name of a part. The part # is 21014 and it's the unit the oil filter attatches to on the block.Has two coolant lines as well in/out.

May not be the part number but casting number for the unit ?
Also this is where the oil sensor plugs directly into.

I need to get a new one but just don't know what the hell to call it O.o
The faster the response the better.

atlantamx3 · Post by **atlantamx3** » November 6th, 2005, 5:25 pm

Sounds to me like an Oil Cooler.

93_mx3_gs · Post by **93_mx3_gs** » November 6th, 2005, 5:28 pm

Hmm. It does cool the oil supposedly but the filter also mounts to it and it mounts to something esle which mounts to the block. Oil filter pedestal ?

jschrauwen · Post by **jschrauwen** » November 6th, 2005, 5:44 pm

atlantamx3 wrote:Sounds to me like an Oil Cooler.

That's it Perry. Page D2-007 of On-Line Shop Manual. The on-line manual is your friend, it may save many queries.
*John*

93_mx3_gs · Post by **93_mx3_gs** » November 6th, 2005, 5:51 pm

Decided to take some pics. where the finger points is where it's all jacked up and won't seal properly.

http://www.geocities.com/shotos_chaos/oil1.jpg

http://www.geocities.com/shotos_chaos/oil2.jpg

93_mx3_gs · Post by **93_mx3_gs** » November 6th, 2005, 6:21 pm

One thing I noticed about it is the massive nut, Is that nut holding 2 pieces together or is that entire unit one thing ?

slimmyslim1420 · Post by **slimmyslim1420** » November 6th, 2005, 7:56 pm

it should be just one piece, also the short name or what some people call it is oil filter adapter, is your leaking, when i done my ZE swap mine was leaking so i replaced the gasket and then everything was fine.

93_mx3_gs · Post by **93_mx3_gs** » November 6th, 2005, 8:08 pm

Well it leaks but not at the block mount. It has damage to the area around the oil filter gasket set area, refer to pictures and pointing.

slimmyslim1420 · Post by **slimmyslim1420** » November 6th, 2005, 8:58 pm

have you found another on yet or are you still looking, also do you still have the stck engine or is it different

atlantamx3 · Post by **atlantamx3** » November 6th, 2005, 9:29 pm

Its the Oil cooler.

I know on the BP that the nut is a 24mm. It should be holding the oil cooler to the bracket. The Size may be different on the k8 though.

Remove the nut, the oil cooler should come off, and will let you replace it if you'd like to.

93_mx3_gs · Post by **93_mx3_gs** » November 6th, 2005, 10:01 pm

slimmyslim1420 wrote:have you found another on yet or are you still looking, also do you still have the stck engine or is it different

Well I need a new one and haven't found one heh. What do these run from the mazda dealer new ?

93_mx3_gs · Post by **93_mx3_gs** » November 6th, 2005, 10:01 pm

atlantamx3 wrote:Its the Oil cooler.

I know on the BP that the nut is a 24mm. It should be holding the oil cooler to the bracket. The Size may be different on the k8 though.

Remove the nut, the oil cooler should come off, and will let you replace it if you'd like to.

Uhh..Head says K8 101 on it so I have no clue about these K series engines.

vozaday2000 · Post by **vozaday2000** » November 6th, 2005, 10:07 pm

93_mx3_gs wrote:
atlantamx3 wrote:Its the Oil cooler.

I know on the BP that the nut is a 24mm. It should be holding the oil cooler to the bracket. The Size may be different on the k8 though.

Remove the nut, the oil cooler should come off, and will let you replace it if you'd like to.
Uhh..Head says K8 101 on it so I have no clue about these K series engines.

ok lets start from the basics. your car is a k8. the k8 is the v6 mx-3 engine. the bp is a 1.8l 4 cyl engine which can be swapped into the 4 cyl mx-3. as he was saying the nut may be a different size from the bp. phone mazda and find out how much it costs. you already know the name, it is a oil cooler. antifreeze goes in and cools off the oil. hence the two hose attachements. the online shop manual found on the mx-3.com homepage is very usefull. it would answer almost all your questions you have asked before. it would also tell you the nut size and how to remove it, install it, etc. read this: http://www.mx-3.com/phpbb2/viewtopic.php?t=3418&start=0

slimmyslim1420 · Post by **slimmyslim1420** » November 6th, 2005, 10:21 pm

[img][img]http://i26.photobucket.com/albums/c146/ ... cooler.jpg[/img] you could also go with an aftermarket part this one is only like $50 bucks US[/img]

PATDIESEL · Post by **PATDIESEL** » November 6th, 2005, 11:49 pm

Slim, that is an oil filter relocation kit, not a replacement oil cooler. (If I see the pic correctly) It won't help solve his problem and it will only complicate what he is already having trouble with.

Read the manual like already suggested and get a new part from Mazda. oh, and make sure that when you place a new oil filter on the car to wet the black ring around the top of the new filter with some clean oil. It will help create a good seal between the oil cooler and the filter.