shifter sitting on exhaust?

goldsberry1 · Post by **goldsberry1** » June 30th, 2003, 10:24 pm

heool, i think my shifter (where it goes through the floor) came out, and is sitting on the exhaust system. i pulled it back up once already, but i think it fell again. how can i keep this from happening? it isnt cool. i acually gets really hot after a while. not enough to really do damage but hot enough to be uncomfortable to hold. i have a metal shifter knob. thanks for any help

dropitlikeitshot · Post by **dropitlikeitshot** » June 30th, 2003, 10:51 pm

hey its a piece that goes to the tranny its suppost to support the shifter usually breaks after some time. it costs 80 bucks to get it new at mazda. its a long stick with a plate at the end of it and it goes right under the shifter.

mx3TT · Post by **mx3TT** » July 1st, 2003, 12:37 am

He is right. When I was taking out my tranny I notcied mine was almost completely rusted thru. So maybe that is what happened to you. Check it out, you will notice it when you go under the car. It is right beside the shift linkage.

goldsberry1 · Post by **goldsberry1** » July 1st, 2003, 12:58 pm

well the bar looked fine like three weeks ago. it slipped out of the hole it goes in. i can pull the shifted up but it wont stay. im not sure why it wont stay.

lucky13 · Post by **lucky13** » July 1st, 2003, 1:07 pm

Well I have an extra on if you want it.

jbreese00 · Post by **jbreese00** » July 1st, 2003, 1:45 pm

Hey do you have a short shifter in, if so what kind, it could be that your C-clip isn't holding, or it could be that the bolts feel off the plate that holds the stock shifter and its bushings in place causing it to drop down.

LLCoolWas · Post by **LLCoolWas** » July 1st, 2003, 2:27 pm

my shifter fell thru when i was doing my ZE swap. its been like that since august 2002, and yes its annoying but it does keep people from driving my car. i picked up a replacement shifter assembly from a junk yard for 10 bucks like 2 weeks after the knuckle fell through, but i havent put it in yet... cause im lazy<p>
(edited for spelling)<p>[ July 01, 2003: Message edited by: Waseem Traish ]</p>

goldsberry1 · Post by **goldsberry1** » July 1st, 2003, 6:39 pm

im going to check it out the rest of the way,(and hopefully fix it) on thusday. ill let you know exactly what it was.

Ramdao · Post by **Ramdao** » July 3rd, 2003, 1:17 am

It happened to me too is the rubber bushing that hold the shifter, right now mine is holding up with a wire wraped around plus a lot of silicone, next time a will take it out and take it to have it fix with a new bushing of poliurethane I´ll bet it´ll hold better.

Marlon · Post by **Marlon** » July 8th, 2003, 5:13 pm

just buy the new part from the dealer, it;s only 70 cnd

pDhMiBsh · Post by **pDhMiBsh** » July 8th, 2003, 11:08 pm

DON'T OVER TIGHTEN THOSE NUTS IF YOU GET A NEW PART!!!!!!!! I FOUND THAT OUT THE HARD WAY WHEN I SNAP 3 OF THE 4 STUDS jsut tightin them "snuggly"

atx_mx3 · Post by **atx_mx3** » July 8th, 2003, 11:08 pm

That exact thing happened to me also the 2nd day i bought my car. I got my friends dad to put 2 spot welds to hold the shifter in place. It has been about 2 weeks now and i havent had any problems. I have been shifting super-slow just incase those welds break. Whatever works right...

MX-3.com

shifter sitting on exhaust?

shifter sitting on exhaust?

Re: shifter sitting on exhaust?

Re: shifter sitting on exhaust?

Re: shifter sitting on exhaust?

Re: shifter sitting on exhaust?

Re: shifter sitting on exhaust?

Re: shifter sitting on exhaust?

Re: shifter sitting on exhaust?

Re: shifter sitting on exhaust?

Re: shifter sitting on exhaust?

Re: shifter sitting on exhaust?

Re: shifter sitting on exhaust?